« previous next »
Pages: 1 ... 3 4 [5]   Go Down

Author Topic: Tiny CNC router  (Read 79171 times)

Offline HS93

  • In Memoriam
  • Hero Member
  • *****
  • Posts: 788
Re: Tiny CNC router
« Reply #100 on: May 21, 2011, 06:55:37 PM »
drip water on the blade and it wont melt back together, I cut a lot of platicard.

Peter
Logged
I am usless at metalwork, Oh and cannot spell either . failure

Offline j45on

  • Sr. Member
  • ****
  • Posts: 380
  • My tiny workshop Location Ashford Kent
Re: Tiny CNC router
« Reply #101 on: May 29, 2011, 03:44:57 PM »
I have made a little round box which my sister has pinched  :wack:
And a madmodder drinks coaster  :lol: just playing around really  ::)

http://i602.photobucket.com/albums/tt102/ja2onx/mm.jpgTiny CNC router
Logged
Jason

Offline spuddevans

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 1618
  • Portadown, Northern Ireland
    • My Photo website
Re: Tiny CNC router
« Reply #102 on: May 29, 2011, 04:20:26 PM »
Nice coaster, give it a lick of clear-coat and slap (gently) a pint on it :thumbup: :thumbup:



Tim
Logged
Measure with a micrometer, mark with chalk, cut with an axe  -  MI0TME

Offline j45on

  • Sr. Member
  • ****
  • Posts: 380
  • My tiny workshop Location Ashford Kent
Re: Tiny CNC router
« Reply #103 on: May 30, 2011, 01:57:54 PM »
Today I decided to re house this case less memory stick
It cost me a small fortune when new so I cant bring myself to throw it away even though it only has 64MB  :lol:

Started by carefully measuring and routing out a side out of a bit of walnut

http://i602.photobucket.com/albums/tt102/ja2onx/1-2.jpgTiny CNC router

Followed by another side,notice the extra pocket I had to add manually  :dremel:
 
http://i602.photobucket.com/albums/tt102/ja2onx/4-1.jpgTiny CNC router

Only now I have finished do I notice I should have made it a bit longer to cover the usb better  :palm:

http://i602.photobucket.com/albums/tt102/ja2onx/3-2.jpgTiny CNC router

All done well nearly I still have to put my name on it

This took nearly 2 hours with a 1mm end mill  :bang:

http://i602.photobucket.com/albums/tt102/ja2onx/6-1.jpgTiny CNC router

The jig to hold it ( this reminds me of the movie 2001  ::) )

http://i602.photobucket.com/albums/tt102/ja2onx/5-1.jpgTiny CNC router

Work in progress

http://i602.photobucket.com/albums/tt102/ja2onx/8.jpgTiny CNC router

Now it's done  :ddb:

http://i602.photobucket.com/albums/tt102/ja2onx/7.jpgTiny CNC router

« Last Edit: May 30, 2011, 03:39:28 PM by j45on »
Logged
Jason

Offline saw

  • Hero Member
  • *****
  • Posts: 1003
  • lucky amateur
    • Svenssons AckordsWerkstad
Re: Tiny CNC router
« Reply #104 on: May 31, 2011, 09:57:16 AM »
nice  :bugeye:
Logged
_________________________
Greetings / Benni
http://myprojecty.wordpress.com/category/steam-engine/
Pages: 1 ... 3 4 [5]   Go Up
« previous next »