« previous next »
Pages: [1]   Go Down

Author Topic: Hot off the mill! Epicyclic first run  (Read 9028 times)

Offline sshire

  • Jr. Member
  • **
  • Posts: 26
  • Country: us
    • LS Editions
Hot off the mill! Epicyclic first run
« on: September 09, 2012, 12:42:35 PM »
Epicyclic Engine. Finished the last bits this morning. First run on air :clap:

After I run it in a bit, polishing and some work on the base.

http://i1126.photobucket.com/albums/l604/sshire/3C348687-1D3C-4A96-BCC8-E45BECD8C1E8-3678-0000052671AA6323.mp4

Best
Stan
Logged
Best,
Stan

Offline Brass_Machine

  • Administrator
  • Hero Member
  • *****
  • Posts: 5516
  • Country: us
Re: Hot off the mill! Epicyclic first run
« Reply #1 on: September 09, 2012, 12:49:54 PM »
Hiya Stan...

That is a nice looking/running engine!

Eric
Logged
Science is fun.

We're all mad here. I'm mad. You're mad.

Offline Raggle

  • In Memoriam
  • Jr. Member
  • *****
  • Posts: 93
  • Newtown, Powys, Mid-Wales
Re: Hot off the mill! Epicyclic first run
« Reply #2 on: September 09, 2012, 07:37:58 PM »
Hypocycloidal  -  don't want to throw Marv in a fit

:)

Ray
Logged
still turning handles  -  usually the wrong way

Offline sshire

  • Jr. Member
  • **
  • Posts: 26
  • Country: us
    • LS Editions
Re: Hot off the mill! Epicyclic first run
« Reply #3 on: September 09, 2012, 08:58:39 PM »
Absolutely correct but I wanted to use Bill Reichart's original name for it. I'm sure Marv will understand  :smart:
Best
Stan
Logged
Best,
Stan

Offline Raggle

  • In Memoriam
  • Jr. Member
  • *****
  • Posts: 93
  • Newtown, Powys, Mid-Wales
Re: Hot off the mill! Epicyclic first run
« Reply #4 on: September 10, 2012, 06:15:34 AM »
I too now understand and sorry if I seemed a bit picky  :(

Ray
Logged
still turning handles  -  usually the wrong way

Offline sshire

  • Jr. Member
  • **
  • Posts: 26
  • Country: us
    • LS Editions
Re: Hot off the mill! Epicyclic first run
« Reply #5 on: September 10, 2012, 07:04:58 AM »
Ray
Picky is good. In most of what we do, "Close enough" won't result in a running engine.   :D

Stan
Logged
Best,
Stan

Offline saw

  • Hero Member
  • *****
  • Posts: 1003
  • Country: se
  • lucky amateur
    • Svenssons AckordsWerkstad
Re: Hot off the mill! Epicyclic first run
« Reply #6 on: September 10, 2012, 07:51:39 AM »
 :bow: :bow: :bow: :bow: :bow:
I am inpressed...
Logged
_________________________
Greetings / Benni
http://myprojecty.wordpress.com/category/steam-engine/

Offline allanchrister

  • Jr. Member
  • **
  • Posts: 55
  • Country: us
Re: Hot off the mill! Epicyclic first run
« Reply #7 on: September 11, 2012, 09:27:13 AM »
Nice Engine, as I hope to build an epicyclic clock (or continue it in the near future), any guidance as to how you cut the internal gears?
Logged
Pages: [1]   Go Up
« previous next »