« previous next »
Pages: [1]   Go Down

Author Topic: Hello from France ...!  (Read 4435 times)

Offline luky luke

  • Newbie
  • *
  • Posts: 1
Hello from France ...!
« on: August 08, 2012, 05:54:10 AM »
Hello,

I am on the Forum HMEM, and it is reading the pages I found a link on this forum, I know I am registered for the month of February, and it is only now that I officially introduce myself, so I ask you all to forgive me, I'll try to show active both here and on HMEM.
I have projects in mind, the problem is that as I would not have finished the retrofit of my CNC milling machine, I can not do the things I planned to do otherwise, but I arrive at final aim.

I wish you all much success in your future and current projects.

Pray for me for the CNC, I'm a veritable Pumpkin in electronics, I must yet to go however by that.
I have already burnt a card-Board (cnc4pc), brief...

When this is over and operational, I do a post with a video on YouTube and a link.

Cordially,
J-M   :beer: 
Logged

Offline saw

  • Hero Member
  • *****
  • Posts: 1003
  • Country: se
  • lucky amateur
    • Svenssons AckordsWerkstad
Re: Hello from France ...!
« Reply #1 on: August 08, 2012, 06:33:26 AM »
Hi and feel very welcome to us  :wave:
Logged
_________________________
Greetings / Benni
http://myprojecty.wordpress.com/category/steam-engine/

Offline spuddevans

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 1618
  • Country: 00
  • Portadown, Northern Ireland
    • My Photo website
Re: Hello from France ...!
« Reply #2 on: August 08, 2012, 06:38:44 AM »
Well hello and welcome  :thumbup: We're glad to have you here with us, and look forward to seeing some of what you are doing.


Tim
Logged
Measure with a micrometer, mark with chalk, cut with an axe  -  MI0TME

Offline PekkaNF

  • Hero Member
  • *****
  • Posts: 2523
  • Country: fi
Re: Hello from France ...!
« Reply #3 on: August 08, 2012, 07:52:19 AM »
Wellcome!

Where from France? I asume it's not Paris, because it gets mentioned over France. Hope it's classic food/vine region.

Post your stuff, even if it is not ready.

PekkaNF
Logged

Offline Brass_Machine

  • Administrator
  • Hero Member
  • *****
  • Posts: 5536
  • Country: us
Re: Hello from France ...!
« Reply #4 on: August 08, 2012, 10:53:48 PM »
Bonjour!  :wave:

Welcome to the collective :borg:

What kind of mill are you converting to CNC? I tried to put together a controller board (hobby CNC), burnt it up, then bought one of the chinese TB boards and then just finally got a decent controller. Spent more money that way than if I had just bought a nice Gecko setup...

Eric


**hopefully I get this right...

Quel genre de moulin à vous convertir au CNC? J'ai essayé de mettre sur pied une carte contrôleur (hobby CNC), elle a brûlé en place, puis acheté l'un des conseils de tuberculose chinois et puis juste a finalement obtenu un contrôleur décent. Dépensé plus d'argent de cette façon que si je venais d'acheter une configuration belle Gecko ...
Logged
Science is fun.

We're all mad here. I'm mad. You're mad.

Offline krv3000

  • Hero Member
  • *****
  • Posts: 2188
  • Country: gb
Re: Hello from France ...!
« Reply #5 on: August 09, 2012, 02:31:37 AM »
hi jump in and have fun
Logged

Offline AussieJimG

  • In Memoriam
  • Sr. Member
  • *****
  • Posts: 381
  • Country: au
Re: Hello from France ...!
« Reply #6 on: August 12, 2012, 12:38:18 AM »
Welcome. I hope you enjoy the site.

Jim
Logged
Pages: [1]   Go Up
« previous next »