« previous next »
Pages: [1]   Go Down

Author Topic: Revolving cylinder engine  (Read 14469 times)

Offline ironman

  • Full Member
  • ***
  • Posts: 157
  • Country: au
Revolving cylinder engine
« on: July 20, 2012, 03:07:12 AM »
                    I made a video of a engine that was completed about four years ago. The idea for the engine came from a website that shows animated engines of all kinds to show how they work.  http://www.animatedengines.com/revcyl.html  I was so intrigued by it I had to build one.  About two years after it was completed I discovered Google patents and found out who built it and when, click onto the link to see the original  patent. http://www.google.com/patents?id=pvlZAAAAEBAJ&printsec=frontcover&dq=revolving+cylinder+steam+engine&hl=en&sa=X&ei=P4kHUJ74KMaYiAeT9tD7Aw&ved=0CDAQ6AEwAA 

[youtube=425,350]http://www.youtube.com
/watch?v=SKjo4i6B_1I?[/youtube]
« Last Edit: July 20, 2012, 03:40:29 AM by dsquire »
Logged

Offline BillTodd

  • Hero Member
  • *****
  • Posts: 1160
  • Country: 00
  • Colchester Essex (where the lathes were made)
Re: Revolving cylinder engine
« Reply #1 on: July 20, 2012, 07:15:16 AM »
Nice :)

Beautifully build too  :headbang:
Logged
Bill

Offline andyf

  • In Memoriam
  • Hero Member
  • *****
  • Posts: 1795
  • Country: gb
    • The Warco WM180 Lathe - Modifications
Re: Revolving cylinder engine
« Reply #2 on: July 20, 2012, 07:47:32 AM »
Splendid  :clap:

It doesn't seem to vibrate while running, so you must have done some careful balancing. I'm surprised that the reciprocating piston doesn't make it jump around a bit.

Andy
Logged
Sale, Cheshire
I've cut the end off it twice, but it's still too short

Offline Stilldrillin

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 4972
  • Country: gb
  • Staveley, Derbyshire. England.
Re: Revolving cylinder engine
« Reply #3 on: July 20, 2012, 08:35:41 AM »
Now..... That's different!  :bugeye:

Love it! Well done!  :clap: :clap:

David D
Logged
David.

Still drilling holes... Sometimes, in the right place!

Still modifying bits of metal... Occasionally, making an improvement!

Offline sbwhart

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 3530
  • Country: gb
  • Smile, Be Happy, Have Fun and Rock Until you Drop
Re: Revolving cylinder engine
« Reply #4 on: July 20, 2012, 10:35:04 AM »
I like that

  :D :D :D :D :D :D :D :D :D :D

Thanks for showing

Stew

Logged
A little bit of clearance never got in the road
 :wave:

Location:- Crewe Cheshire

Offline ironman

  • Full Member
  • ***
  • Posts: 157
  • Country: au
Re: Revolving cylinder engine
« Reply #5 on: July 22, 2012, 01:24:28 AM »
andyf   The piston does not reciprocate It is a very simple engine to look at but is very complex to design. Take a close look at the counterweight it is not big enough! When I run it faster than on the video it starts to jump around and when the counterweight is taken off it jumps all over the place! This engine is my all time favorite, I always love to see it run.
Logged

Offline AndyB

  • Full Member
  • ***
  • Posts: 192
  • Country: england
  • Cry 'god for Harry, England, and Drummond lathes'
Re: Revolving cylinder engine
« Reply #6 on: July 22, 2012, 12:51:25 PM »
Nice one! :clap: :clap: :clap:

I can imagine the headache designing it just for the intake and exhaust flows and the valve timing :bow: :bow:

Andy
Logged
Waveney Valley, Suffolk/Norfolk Border

Offline m_kilde

  • Jr. Member
  • **
  • Posts: 11
Re: Revolving cylinder engine
« Reply #7 on: July 25, 2012, 01:51:09 PM »
Ironman

I too would like to pay my respect for that wonderful engine you have build.

 :bow:

Logged

Offline Ross

  • Full Member
  • ***
  • Posts: 130
  • Country: gb
    • Ross' steam engines
Re: Revolving cylinder engine
« Reply #8 on: August 31, 2012, 08:33:16 PM »
Wow that's a really clever design And build!
Logged

Offline Chuck in E. TN

  • Hero Member
  • *****
  • Posts: 572
  • Country: us
  • USAF Retired
Re: Revolving cylinder engine
« Reply #9 on: August 31, 2012, 08:49:44 PM »
Ironman, that's an amazing engine, and beautifully built. Did you work out the design on your own from the animation, or did you have plans?
Chuck
Logged
Chuck in E. TN
Famous TN last words: "Hey ya'll, watch this..."
MicroMark 7x14, HF X2 mill, Green 4x6 saw. Harbor Freight 170A mig

Offline krv3000

  • Hero Member
  • *****
  • Posts: 2188
  • Country: gb
Re: Revolving cylinder engine
« Reply #10 on: September 01, 2012, 07:22:01 PM »
ooo nice
Logged
Pages: [1]   Go Up
« previous next »