MadModder
Welcome,
Guest
. Please
login
or
register
.
1 Hour
1 Day
1 Week
1 Month
Forever
Login with username, password and session length
News:
Check out the latest projects here:
Project Logs
Home
Help
Search
Login
Register
MadModder
»
Gallery, Projects and General
»
The Design Shop
»
X2 X axis table stop
« previous
next »
Print
Pages: [
1
]
Go Down
Author
Topic: X2 X axis table stop (Read 11656 times)
Chuck in E. TN
Hero Member
Posts: 572
Country:
USAF Retired
X2 X axis table stop
«
on:
July 05, 2011, 01:42:49 PM »
I would like to make a couple of clamp on table stops for the X axis of my X2 mill. Anyone made these and have a drawing or pic to share?
Chuck in E. TN
Logged
Chuck in E. TN
Famous TN last words: "Hey ya'll, watch this..."
MicroMark 7x14, HF X2 mill, Green 4x6 saw. Harbor Freight 170A mig
wheeltapper
Sr. Member
Posts: 345
Country:
Spixworth Norfolk
Re: X2 X axis table stop
«
Reply #1 on:
July 05, 2011, 03:20:47 PM »
Hi
here's some I made for my mill (a Chester Conquest ).
they might give you some ideas.
Roy
Logged
I used to be confused, now I just don't know.
andyf
In Memoriam
Hero Member
Posts: 1795
Country:
Re: X2 X axis table stop
«
Reply #2 on:
July 05, 2011, 04:36:58 PM »
There are some permanent (as opposed to temporary clamp-on) X and Y stops shown here, Chuck:
http://mikesworkshop.weebly.com/mill-table-stops-and-locks.html
.
They are on an X1, but the general design would probably work just as well on an X2.
Andy
Logged
Sale, Cheshire
I've cut the end off it twice, but it's still too short
Chuck in E. TN
Hero Member
Posts: 572
Country:
USAF Retired
Re: X2 X axis table stop
«
Reply #3 on:
July 05, 2011, 05:14:23 PM »
Thanks, Roy, and Andy for your replies. I like the simplicity of Roy's design. I will study both.
Roy, did you add a brass point to the locking bolt, or just a push piece?
Chuck in E. TN
Logged
Chuck in E. TN
Famous TN last words: "Hey ya'll, watch this..."
MicroMark 7x14, HF X2 mill, Green 4x6 saw. Harbor Freight 170A mig
wheeltapper
Sr. Member
Posts: 345
Country:
Spixworth Norfolk
Re: X2 X axis table stop
«
Reply #4 on:
July 06, 2011, 08:42:03 AM »
Hi
the brass point is inserted into the end of the bolt.
these stops were a quick and dirty fix for a particular purpose but they have got certain limitations.
Roy
Logged
I used to be confused, now I just don't know.
Chuck in E. TN
Hero Member
Posts: 572
Country:
USAF Retired
Re: X2 X axis table stop
«
Reply #5 on:
July 06, 2011, 10:01:06 AM »
Roy,
What are the limitations you've found?
Chuck in E. TN
Logged
Chuck in E. TN
Famous TN last words: "Hey ya'll, watch this..."
MicroMark 7x14, HF X2 mill, Green 4x6 saw. Harbor Freight 170A mig
John-Som
Jr. Member
Posts: 98
Re: X2 X axis table stop
«
Reply #6 on:
July 06, 2011, 10:13:07 AM »
Thanks guys, just what I've been looking for. Such a setup on my X2 (Conquest) mill will reduce my reliance on my cheap DRO system. As I see it I will be able to do the initial setup using my DRO system and once the stops are positioned I shan't need to rely on my temperamental DROs for repeat travel. It's usually on the back and forth travelling that my DROs decide to throw a wobbly.
I shall be trying to adopt the ideas on Mikes Workshop but the fixtures will have to be adjusted to accommodate my DRO installation.
http://mikesworkshop.weebly.com/mill-table-stops-and-locks.html
John-Som
Logged
start-model-engineering.co.uk - a friendly place for model engineering beginners
Print
Pages: [
1
]
Go Up
« previous
next »
MadModder
»
Gallery, Projects and General
»
The Design Shop
»
X2 X axis table stop