Author Topic: A Stirling engine  (Read 15904 times)

Offline cidrontmg

  • Full Member
  • ***
  • Posts: 229
  • Country: pt
A Stirling engine
« on: October 27, 2010, 06:54:38 AM »
Another gamma Stirling. Both strokes are 15 mm, work piston is 12 mm dia graphite, displacer is 17.5 mm dia and the glass cylinder is 18.5 mm inside.


Another picture


This is what she drinks, no meths, straight stuff...


And here she runs


The flywheels have some balancing, but not enough, she walks around the table somewhat.
The burner tube is too long, the wick stands too high. Have to cut a bit off it, and fix it to a proper board. No polishing yet, just finished it yesterday so it would run. Always nice when a new machine behaves   :)
 :wave:
Olli
Penafiel
Portugal

Offline AdeV

  • Madmodder Committee
  • Hero Member
  • *****
  • Posts: 2435
  • Country: gb
Re: A Stirling engine
« Reply #1 on: October 27, 2010, 07:11:44 AM »

Another picture


This is what she drinks, no meths, straight stuff...



Beautiful work, that's a classy looking engine.

I hope to emigrate to Portugal in a couple of years time (approx), nice to know where I can get rubbing alcohol :)
Cheers!
Ade.
--
Location: Wallasey, Merseyside. A long way from anywhere.
Occasionally: Zhengzhou, China. An even longer way from anywhere...

Offline Brass_Machine

  • Administrator
  • Hero Member
  • *****
  • Posts: 5516
  • Country: us
Re: A Stirling engine
« Reply #2 on: October 27, 2010, 10:02:33 AM »
Self build? Pictures of the build process? did you follow plans?

Very nice!

Eric
Science is fun.

We're all mad here. I'm mad. You're mad.

Offline Stilldrillin

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 4972
  • Country: gb
  • Staveley, Derbyshire. England.
Re: A Stirling engine
« Reply #3 on: October 27, 2010, 10:18:45 AM »
Cid.
That's beautiful!   :bugeye:

Runs so smoothly/ quietly too.   :clap:

Well done!  :thumbup:

David D
David.

Still drilling holes... Sometimes, in the right place!

Still modifying bits of metal... Occasionally, making an improvement!

Offline sbwhart

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 3530
  • Country: gb
  • Smile, Be Happy, Have Fun and Rock Until you Drop
Re: A Stirling engine
« Reply #4 on: October 27, 2010, 11:45:04 AM »
Good Job A great runner

Stew
A little bit of clearance never got in the road
 :wave:

Location:- Crewe Cheshire

Offline cidrontmg

  • Full Member
  • ***
  • Posts: 229
  • Country: pt
Re: A Stirling engine
« Reply #5 on: October 27, 2010, 12:19:13 PM »
Self build? Pictures of the build process? did you follow plans?

Very nice!

Eric
Yes, self built, following a German design and plans. I also bought the glass cylinder, the graphite for the piston and 2 ball bearings from Germany. And of course, made some slight design changes... No pictures about the build, sorry. I´m planning to do another bigger machine following the same basic design. I just bought a new camera/camcorder, I hope I can take pictures about that build.
Olli
Penafiel
Portugal

Rob.Wilson

  • Guest
Re: A Stirling engine
« Reply #6 on: October 28, 2010, 05:32:05 PM »
 :bugeye: Great stuff  :bow: :bow: :bow: :bow: :D


great runner too :clap: :clap: :clap: :clap:



Rob

Offline John Hill

  • The Artful Bodger
  • Madmodder Committee
  • Hero Member
  • *****
  • Posts: 2016
  • Country: nz
Re: A Stirling engine
« Reply #7 on: October 28, 2010, 07:40:00 PM »
A beautiful piece of work! :thumbup:
From the den of The Artful Bodger

Offline Dean W

  • Hero Member
  • *****
  • Posts: 571
  • My kingdom for a lathe!
    • Projects web pages
Re: A Stirling engine
« Reply #8 on: October 28, 2010, 10:42:23 PM »
Very nice, Olli!  You do mighty fine work.
Dean W.

Shop Projects:
http://www.deansphotographica.com/machining/projects/projects.html

Praise the Lord and pass the Carbide!

Offline Brass_Machine

  • Administrator
  • Hero Member
  • *****
  • Posts: 5516
  • Country: us
Re: A Stirling engine
« Reply #9 on: October 29, 2010, 01:37:16 PM »

 Yes, self built, following a German design and plans. I also bought the glass cylinder, the graphite for the piston and 2 ball bearings from Germany. And of course, made some slight design changes... No pictures about the build, sorry. I´m planning to do another bigger machine following the same basic design. I just bought a new camera/camcorder, I hope I can take pictures about that build.

Where can one find the plans?

Thanks
Eric
Science is fun.

We're all mad here. I'm mad. You're mad.

Offline j45on

  • Sr. Member
  • ****
  • Posts: 380
  • My tiny workshop Location Ashford Kent
Re: A Stirling engine
« Reply #10 on: October 29, 2010, 01:42:39 PM »
Impressive workmanship  :bow:
Jason