Author Topic: First bit of proper turning and threading. (Read 11235 times)

dawesy · « **on:** February 01, 2015, 11:11:27 AM »

Made a start on a filler neck today.
Turned from alloy bar (not sure of grade) with a 12tpi thread.
Quite happy with how it's turned out for my first real attempt.

Ready for boring.

All done.

Now to make a cap for it

steampunkpete · « **Reply #1 on:** February 01, 2015, 11:52:02 AM »

If that is your first attempt you are destined for MadModder greatness.

If you don't mind us asking, what is it a filler-cap for?

Would an undercut to thread root diameter at the inner end of the thread have made life easier, or couldn't you do that for this application?

dawesy · « **Reply #2 on:** February 01, 2015, 01:21:03 PM »

Thanks. I'm quite chuffed with it

I've turned bits but this is really the first bit with threading etc.
it's for a water/ methanol tank.
It's not clear from the pics but there is a thread undercut against the shoulder.
Parting off was really the toughest bit although I now have to make a cap that fits lol.

krv3000 · « **Reply #3 on:** February 01, 2015, 03:12:08 PM »

brill well dun

Bangkok Mick · « **Reply #4 on:** February 01, 2015, 08:53:39 PM »

Looks like a job well done.

dawesy · « **Reply #5 on:** February 01, 2015, 11:51:13 PM »

Thanks guys.
Think I've got the hang of screw cutting now. Just took my time.
Need to make some more change wheels for the lathe though as I'm a few missing which limits the threads I can cut

vtsteam · « **Reply #6 on:** February 02, 2015, 11:20:09 AM »

Dawesy, I was that cut on your Churchill Redman lathe? It does look great!

RussellT · « **Reply #7 on:** February 02, 2015, 12:24:43 PM »

You've got a nice finish on that.

Have you decided where the seal is going to go - or is is going to do without?

Russell

Stilldrillin · « **Reply #8 on:** February 02, 2015, 02:35:43 PM »

Sweet!

Well done.....

David D

RotarySMP · « **Reply #9 on:** February 02, 2015, 04:50:08 PM »

"Turned from alloy, not sure what grade"

Obviously really shiny grade. Robert that same alloy.

Mark

dawesy · « **Reply #10 on:** February 03, 2015, 04:49:27 AM »

Thanks guys

Yep all done on the old Churchill ;)
Cap all done now bar knurling

Seals going in the cap Russell
You can just about see the undercut in this pic

Going to practice knurling first before I do the cap :/
Also going to trim down the threads on the neck as I think I must have knocked the verniers when I measured it to get the depth for the cap

BillTodd · « **Reply #11 on:** February 03, 2015, 03:23:58 PM »

Caution: If that is stainless steel - grease the threads with copper slip (anti-seize) or you may not get it apart again !

dawesy · « **Reply #12 on:** February 03, 2015, 04:07:57 PM »

Thanks for the heads up bill but its aluminium ;)

PJW · « **Reply #13 on:** March 19, 2015, 09:23:12 AM »

A nice bit of turning, a job to be proud of

Peter

dawesy · « **Reply #14 on:** March 19, 2015, 09:24:34 AM »

Thank you Peter. The tank is almost finished

RobWilson · « **Reply #15 on:** March 19, 2015, 02:39:37 PM »

Nicely done

Whats the tank for /to be fit to ?

Rob

dawesy · « **Reply #16 on:** March 19, 2015, 04:38:39 PM »

Water injection on my MR2 Rob

Still got to turn and weld the bosses for the level tube and take off.
This is it in situ

Sample of the alloy has been sat in the water/methanol mix for a while now and no signs of a reaction yet.

RobWilson · « **Reply #17 on:** March 19, 2015, 05:12:42 PM »

Arrh

, did you make the tank Lee ?

Welding looks looks very tidy

Rob

dawesy · « **Reply #18 on:** March 19, 2015, 08:46:34 PM »

Thanks rob. Yes all my own work

Welds aren't as smooth as I'd like but I'm still learning and aluminium is a hard mistress. Doesn't help that my foot pedal has given up the ghost

News:

Author Topic: First bit of proper turning and threading. (Read 11235 times)

RobWilson

RobWilson