Building Stuarts Compound Steam Engine

[NickG]

Benni,

very nice work it looks really pretty.  One question though, aren't the cross heads meant to be screwed home onto the shoulders of the rods? If not you might get the pistons hitting the top covers. Worth checking that length.

Nick

[saw]

Yes NickG it's very impotante that the lenght is correct. Right now I have only gone after drawing from Stuart but I assume that I need to make some adjustments. 

[NickG]

Yeah, I am sure drawing wouldn't intend it to be like that, have a look on the assembly drawing - I don't think there'll be a gap like on yours. This is where the standard of model engineering drawings fall short or need some interpretation, you can't actually make these things to the drawing and you haven't so far or it wouldn't assemble.

More than likely what's happened is you can't actually get to the bottom of the hole with the tap, so it either needs to be drilled and tapped a little deeper, or the thread on the rod needs shortening or a large chamfer put on the end.

 

[saw]

Wow, it's a miss of me   
...but it's easy to fix. 
Thanks NickG for pointed out 

[NickG]

No problem, I don't think it's an easy task to machine a kit from castings and model engineering drawings - especially if there are no instructions.

For example, if you were to send out parts to different companies to be manufactured, they would not assemble because model engineering drawings aren't well specified enough, it's up to the machinist to interpret what fit is needed where etc.

I've never machined a model from castings yet, I don't think I'd do as good a job as you have - I just happened to notice the gap.

Keep up the good work. 

[saw]

Connecting rod
Hello Gentlemen.
At last I found some time to continue my build of Stuarts Compound Engine. 
This time it’s the connecting rod, and it is a very important part of the engine.
They have to be in straight line, square and the dimension must be exact.
Here is the casting of the connecting road, as you can see there is plenty of material to remove.
 Building Stuarts Compound Steam Engine
First I have to square the bottom end with an end mill.
 Building Stuarts Compound Steam Engine
And after that I have to draw out and mark where the holes for the crankshaft should be. 
Building Stuarts Compound Steam Engine
Next I drilled the top and bottom end…
 Building Stuarts Compound Steam Engine
 Building Stuarts Compound Steam Engine
… and this is for my set up in my lathe.
 Building Stuarts Compound Steam Engine
It shows up that this set up was not so good idea, so I changed to this.
 Building Stuarts Compound Steam Engine
And now I could finish some parts on the lathe.
 Building Stuarts Compound Steam Engine
Then I drilled some holes for the bolt before I partial bottom end in two parts.
 Building Stuarts Compound Steam Engine
Then I use  a hacksaw…
 Building Stuarts Compound Steam Engine
…and there was two parts of each connecting roads.
 Building Stuarts Compound Steam Engine
Next I drilled the hole for the crankshaft.
 Building Stuarts Compound Steam Engine
And some more turn on the lathe.
 Building Stuarts Compound Steam Engine
This set up looks crazy but it is to help me drilling the holes square for connecting to the crosshead.
 Building Stuarts Compound Steam Engine
After that some milling.
 Building Stuarts Compound Steam Engine
Here I try to round off the top part.
 Building Stuarts Compound Steam Engine
 Building Stuarts Compound Steam Engine
And here we go, two connecting roads are finish.
 Building Stuarts Compound Steam Engine
And then I mounted the connecting roads on the engine.
 Building Stuarts Compound Steam Engine
This was a little tricky to do but another part is finish,  but still there is a lot more to do.
I’ll be back

[andyf]

It's looking really good, Benni 
Andy

[Meldonmech]

Hi Benni
                   What a first class build presentation and so detailed, nearly there now.

                                                            Regards David

[saw]

Steam Chests
Hello Gentlemen. 
Now it’s time to take care of the steam chest. This is a very important piece of the steam engine, it’s truly the heart of the steam engine.
I’ll begin with the cover. The cover has a spigot on the backside so it’s very easy to set up in the lathe.
Building Stuarts Compound Steam Engine
   
Here I have set up the cover in my lathe for removing the cast skins.
Building Stuarts Compound Steam Engine
 
After that I move the cover to my mill so I can mill the side in square.
 Building Stuarts Compound Steam Engine

Then with a hacksaw I cut of the spigot.
Building Stuarts Compound Steam Engine
 
Then flatten the backside.
Building Stuarts Compound Steam Engine
 
Now I have to mark out for all holes…
 Building Stuarts Compound Steam Engine

… and drilled the holes and countersink the holes.
Building Stuarts Compound Steam Engine
 
I feel radar pleased with the result.
Building Stuarts Compound Steam Engine
 
I’ll continue with the steam chests.
In the lathe I set up the steam chest in a four jaw chuck and took some turn on the top making the valve rod guide…
Building Stuarts Compound Steam Engine
 
… and the bottom for the packing gland.
Building Stuarts Compound Steam Engine
 
With a good fill I smooth the packing gland.
Moving over to the mill for milling both sides to the steam chest…
Building Stuarts Compound Steam Engine
 
Then I milled both sides…
Building Stuarts Compound Steam Engine
 
… and the insides as well.
Building Stuarts Compound Steam Engine
 
And now I have four pieces so far.
Building Stuarts Compound Steam Engine
 
Next, drilling the holes for the valve rod guide…
Building Stuarts Compound Steam Engine
 
…and then using an end mill for the packing gland.
Building Stuarts Compound Steam Engine
 
After that I drilled the hole for the steam inlet.
Building Stuarts Compound Steam Engine
 
A new setup so I could drill the hole into the steam chest.
Building Stuarts Compound Steam Engine
 
After two holes I’ll use bolt and nuts to hold the two pieces together.
Building Stuarts Compound Steam Engine
 
And here we go.
Building Stuarts Compound Steam Engine
 
Then, using the cover I drilled the holes in the cylinder block…
Building Stuarts Compound Steam Engine
 
…and threaded the cylinder block with help of a top hat.
Building Stuarts Compound Steam Engine
 
The stem chest with the cover seams to fits very well.
Building Stuarts Compound Steam Engine
 
Next, the packing glands.
Building Stuarts Compound Steam Engine
 
First I have to cutting of the pieces…
Building Stuarts Compound Steam Engine
 
…and the in the lathe for some turns, flatten one side and center drill /drilled a hole.
Building Stuarts Compound Steam Engine
 
Then I use a spigot so I could turn the other side.
Building Stuarts Compound Steam Engine
 
Marking for the holes for the stud, then threaded and then drilling through …
Building Stuarts Compound Steam Engine
Building Stuarts Compound Steam Engine
 
 
…and after some good work with my fill I have to check so it fits well.
Building Stuarts Compound Steam Engine
 
No it’s time for the valve roads.
Building Stuarts Compound Steam Engine
 
After cutting the parts I took some turn in the lathe and threaded the valve roads …
Building Stuarts Compound Steam Engine
 
…in both end.
Building Stuarts Compound Steam Engine
 
And now there is to more pieces to the steam chest.
Building Stuarts Compound Steam Engine
 
Next, the valve.
Building Stuarts Compound Steam Engine
 
First in the mill I flatted both sides…
Building Stuarts Compound Steam Engine
 
…trying to have a smooth side on the valve.
Building Stuarts Compound Steam Engine
 
Then drilled throe …
Building Stuarts Compound Steam Engine
 
…and then mill a track in the valve.
Building Stuarts Compound Steam Engine
 
And now two more pieces finish.
Building Stuarts Compound Steam Engine
 
Then I cut of a piece of bras…
Building Stuarts Compound Steam Engine
 
…and mark up for a hole to be drilled…
Building Stuarts Compound Steam Engine
 
…and threaded…
Building Stuarts Compound Steam Engine
 
…and again check for fitting.
Building Stuarts Compound Steam Engine
 
Then with a hacksaw and a fill I’ll got this…
Building Stuarts Compound Steam Engine
 
…and it fits well in the steam chest.
Building Stuarts Compound Steam Engine
 
And now another piece is finish.
Building Stuarts Compound Steam Engine
 
This update took some times, it was radar many pieces to make and they have to be accurate, but nothing bad happened so I am very pleased over this update.
I’ll be back.
 

[Stilldrillin]

That's good work you've done Benni! 

Very well shown, too. 

David D

[andyf]

Nice work, Benni!

I see you have been converting all the inch dimensions on the plans to mms. Are you using the nearest ISO metric threads instead of the BA ones on the plans?

Andy

[saw]

Hi and thanks for nice comments.
andyf: No I am using BA but I need to understand the dimensions so I have program in Visual Studio a small program that convert inch to mm. Everything so an old man can build this engine  .

[NickG]

Wow, Benni, that was a huge installment. You seem to be improving with each one, well done - fantastic work 

[DavidA]

Benni,

You are an inspiration !

Most excelent work.

Dave

[NickG]

Benni, just a couple of small things to point out that may help with running. You may already have done but you should lap the valves and port faces of cylinder block on fine wet & dry on a flat surface then with oil in a figure of 8 motion to ensure they are both nice and flat and make a good seal. Also the pocket of the inside of the valves should be an accurate size not left as rough casting. The length and position of the pocket are critical. You may need to size this dependent on how you ports came out rather than go straight from the drawings.

[saw]

NickG: Thanks for coments, I have not lap the valves and portface, but I have not forgot that. I thought that when I have manufactu all pieces I should strip down the whole engine, polish and adjust everything.
About the inside of the valve, I did not know that but now when you tell me, I will do that. Thank you very much NickG to be so accurate. 

[saw]

Eccentric Rods
Hello Gentlemen. 

Now it’s time for the head, that connecting the valve road with the eccentric rods.
A piece of mild still in the lathe…



…and some turns and center drill.
After drilling  and cut off…


…then in the mill some more drilling for connecting to the eccentric rods.


Then with an end mill…


…and it begun to look as a head.


Then some threading for connecting to the valve rods…


…and then finish off with some end mill.


After some work with a good fill and some polish…


…and here is how it looks on the engine. 


Next the eccentric.


First I have to center drill…


…then some turn on the lathe…


…and then turning the small track on the eccentric.


Half way done.


And now a very crazy setup, I was force to use the cuck from my unimat be course   
I was unable to clamp it to the original chuck. 


Center drill…


…and drilled…


… and reaming.


Then drilling and trheading for the stop screw.


And this job was finish…


…and mounted. 


Now the last part, the eccentric rod.


First I have to measure and mark out where to cut and where to drill…


…then drill the hole for the bolts before cutting off the parts.


I’ll then use an end mill so the bolts head could fit better…


…on both side.


Then with my hacksaw I cut the part…


…and threading the bottom part.


Some turns on the lathe…


…and then borring the inside…


…and checking so the hole fits well to the eccentric.

Next I have done a little special for turning the track inside the eccentric rod. 


And again checking the result…


…then back to the mill for milling the surface…


…and then some more milling.


And now some filling and polish…


…and the result…


…and then mounting to the engine. 


Well she is beginning to look like the real thing. It is not so many parts to manufacturing but it’s still long way to go before she’s run.
I’ll be back.
Benni

[Rob.Wilson]

  coming along Very nicely Benni 


Rob

[NickG]

Yep, looks lovely Benni. Not long before you start setting the timing etc- which am not quite sure how on a compound like this. Will be good to see, looking forward to it.