MadModder

Gallery, Projects and General => Member Videos => Topic started by: doubleboost on January 15, 2014, 07:11:13 PM

Title: New MIG Welder
Post by: doubleboost on January 15, 2014, 07:11:13 PM

     [youtube]flA1fNqXMGE[/youtube]

John

Title: Re: New MIG Welder
Post by: dawesy on January 16, 2014, 04:28:59 AM

Looks like a nice substantial unit there john. Wire feed looks decent too, usually the biggest problem with the smaller hobby units.
Looking forward to seeing it in use.

Title: Re: New MIG Welder
Post by: doubleboost on January 16, 2014, 02:01:37 PM

     [youtube]cENeZrmm_b8[/youtube]

Title: Re: New MIG Welder
Post by: Pete W. on January 16, 2014, 02:44:18 PM

Hi there, John,

I can't read Reply #2 - is it that misplaced square bracket again? 

Title: Re: New MIG Welder
Post by: dawesy on January 16, 2014, 03:15:52 PM

Very nice john. Been there and dropped a spool before and had the end slip out my fingers. Your right 'b£&@cks is the right word :)

Title: Re: New MIG Welder
Post by: krv3000 on January 19, 2014, 01:49:46 PM

well dun john do you want a flow meter for it

Title: Re: New MIG Welder
Post by: doubleboost on January 19, 2014, 01:54:21 PM

Hi
Bob
Just put the flow meter on that you gave me  :D :D
John

Title: Re: New MIG Welder
Post by: doubleboost on January 25, 2014, 06:36:06 PM

[youtube]http://www.youtube.com/watch?v=oTPEACrW0EE&list=PLwzZw6FLeTREi7Htfhn0HOaB9rh-Z41uW&feature=c4-overview-vl[/youtube]

Title: Re: New MIG Welder
Post by: S. Heslop on January 26, 2014, 12:18:28 PM

Got a good laugh at the end of this one.

Title: Re: New MIG Welder
Post by: John Rudd on January 26, 2014, 01:52:11 PM

John just never ceases to amaze me..... :

But his sense of humour is just inimitable   :lol:

Title: Re: New MIG Welder
Post by: doubleboost on February 03, 2014, 04:45:17 PM

[youtube]http://www.youtube.com/watch?v=tafdSDuJRXw[/youtube]

Title: Re: New MIG Welder
Post by: krv3000 on February 03, 2014, 05:10:24 PM

well dun you will be making a bote for that engine to go in next

Title: Re: New MIG Welder
Post by: micktoon on February 03, 2014, 06:05:47 PM

Hi John , I cant wait to see this baby get cranked right up  :ddb: its getting nice welds in that latest vid on the half setting I bet it will melt in lovely on full power  :drool:, my 165 amp Murex is not as good at thicker stuff as this welder was on this vid. I cant complain as its been faultless for a good 20 odd years and just does the job with no hitches in general.
  Cheers Mick.

Title: Re: New MIG Welder
Post by: doubleboost on February 11, 2014, 05:31:37 PM

[youtube]http://www.youtube.com/watch?v=FjBO_FCg1bk#t=16[/youtube]