Recent Posts

Pages: [1] 2 3 ... 10
1
The Water Cooler / Re: Car magic
« Last post by NormanV on Today at 07:27:45 AM »
Try his car door? And get arrested :D
I'll try the foil, and no they are not the same make mine's Volvo his MG
2
The Water Cooler / Re: Car magic
« Last post by Muzzerboy on Today at 07:13:08 AM »
Have you tried the door to see if you can get in? Are they both the same brand? I can't understand why the lights would come on simply driving past - perhaps a coincidence? Wrap the fob in foil and see if it really is causing this.
3
The Water Cooler / Car magic
« Last post by NormanV on Today at 06:48:44 AM »
Here's a strange thing, my neighbour  has a new car and when I press the remote locking button on my keyfob his side lights come on. Earlier today as I drove  past his lights also came on. Any thoughts on what could be happening here?
4
Radio Control Models / Re: 1/16 Scale RC Truck parts
« Last post by tom osselton on February 12, 2025, 05:04:50 PM »
 :beer: I’m watching too.
5
Member Videos / Homemade Headstock Lathe 1 fondry work
« Last post by celsoari on February 12, 2025, 03:14:40 PM »
Homemade Headstock Lathe 1 fondry work



Greetings from Brazil

Celso Ari
6
Radio Control Models / Re: 1/16 Scale RC Truck parts
« Last post by ozzie46 on February 12, 2025, 06:49:50 AM »
another following

ron
7
Radio Control Models / Re: 1/16 Scale RC Truck parts
« Last post by BillTodd on February 12, 2025, 03:02:36 AM »
Unless... I'm just a figment of your imagination! 


(In which case  would you be so kind, as to imagine me in a slightly less damp , cold country, with two working knees)
8
Radio Control Models / Re: 1/16 Scale RC Truck parts
« Last post by ddmckee54 on February 11, 2025, 09:48:09 PM »
Thanks Bill, now at least I KNOW that I'm not just talking to myself.
9
Radio Control Models / Re: 1/16 Scale RC Truck parts
« Last post by BillTodd on February 11, 2025, 01:57:59 PM »
I'm still quietly following along ;-)
10
Radio Control Models / Re: 1/16 Scale RC Truck parts
« Last post by ddmckee54 on February 10, 2025, 10:42:36 PM »
Seems like I've just been talking to myself for a while, but there has been a little progress made. 


I cut down the partial axle that was shown previously, and took a little more care with the diameter this time.  I glued the turned stub into the brass tube using a Vee-block to align the parts as the Loctite cured.  The original axle shafts were about 101.8mm, I rounded this up to 102mm.  I had calculated that I needed to take 28mm out of each axle shaft.  But I wanted this "practice" axle to be too long, so I added another 4mm onto my target length.  I then cut the 5mm diameter end of the outboard axle stub to length and turned a 3mm OD stub 10mm long on that end.  I then slipped the axle shaft together and checked the length with my trusty HF 4" caliper.  After deciding it was good enough for "gubmint" work I glued the parts together, again using the Vee-block for alignment

After things had cured for a few hours I couldn't wait anymore and decided to test fit the axle in my 3D printed Frankendiff housing.  I had added another 4mm onto my calculated axle length, and there's a 4mm gap between the 12mm hex driver and the outer bearing.  So I've got a working procedure for narrowing my WLToys rear axles for use on my Bruder truck RC conversions.

Now I only have to do this at least 4 more times and I'll be able to move on to actually building the truck.  I said at least 4, but it will probably be 6 times since I'm 99.44% sure that I'm gonna swipe a very good idea from Blender on another forum and also build a powered steer axle.

Don
Pages: [1] 2 3 ... 10