MadModder

Gallery, Projects and General => Project Logs => Topic started by: Doc on October 04, 2018, 09:36:24 PM

Title: Miniature coil winder
Post by: Doc on October 04, 2018, 09:36:24 PM
Ok going to build (or attempt) to build miniature coils first need to build the winder. I'll post here if there is any interest in it if not no big deal we will see.
Anyway the first thing will be the gear package for it. It will be a version of the Side Winder miniature coil winder from Bob Shores book.  The book is a very good book if you want info on coils and windings  I recommend it.

Title: Re: Miniature coil winder
Post by: PK on October 04, 2018, 11:49:08 PM
Really interested as I may be in the same boat soon....
Title: Re: Miniature coil winder
Post by: John Rudd on October 05, 2018, 03:27:52 AM
Bring it on Doc, waiting to see it finished.. :dremel:
Title: Re: Miniature coil winder
Post by: ddmckee54 on October 05, 2018, 03:09:42 PM
Whatcha gonna wind the itty-bitty coils for?

Don
Title: Re: Miniature coil winder
Post by: Doc on October 05, 2018, 03:42:25 PM
The IC engines I've built all have ignition systems already. I just want to try and see if I can do it, just to do it. Always wanted to try finally decided to give it a try. And who knows if I do succeed I may have  another IC engine build in the future that could use one ;)
Title: Re: Miniature coil winder
Post by: Doc on October 05, 2018, 04:03:05 PM
Ok setting up machine to cut gears for the winder.

There are several gears needed all are 48dp  need one 16t three 32t one 72t and one 81t. Going to start with the 16t then the 32t after that probably the 72t as my indexer will index even degrees. For the 81t I may set up the machine to make my index strip for me first. Sure wish I would have gotten the A  axis when I got my machine. That would have mad things so simple oh well I always said I like a challenge. Haha


Anyway here is a video of setting up machine.

Title: Re: Miniature coil winder
Post by: Doc on October 06, 2018, 09:50:28 AM
Ok cutting the first gear a 16t x 48dp  After this I will cut the 32t then the 72t and last will be the 81t. But before I cut the 81t I will set up the machine to create my index strip.

Here is #3

Title: Re: Miniature coil winder
Post by: awemawson on October 06, 2018, 11:19:10 AM
Interesting way of cutting your gears there Doc  :thumbup:

I'm trying to get my head round whether the gear is actually being 'generated' as it would be with a normal hob that has a lead to the cutter, and the work piece and hob rotate together. I suspect not  :scratch:

Much easier cutter to make though, and you've set me thinking about doing it completely automated with my 4th axis on my CNC mill. The 4th axis cannot be used like a continuously rotating spindle, as you would need for hobbing, but it can easily index tooth by tooth as you were doing manually.
Title: Re: Miniature coil winder
Post by: Doc on October 06, 2018, 02:46:18 PM
  I use to cut my gears with a single tooth cutter but after making a hob cutter and cutting them this way I have changed.
I used a spread sheet put together by a member on another board where has posted it. It is a very useful sheet. Gives you all the info for making the hob cutter. I've used this method a couple times now and work's pretty darn good. 
Title: Re: Miniature coil winder
Post by: awemawson on October 06, 2018, 02:51:02 PM
I suppose it's akin to a Sunderland Gear Planer in motion, in that you are pushing a rack form through the blank then indexing a tooth. OK the rack is rotating, which makes the cutting action easier
Title: Re: Miniature coil winder
Post by: philf on October 06, 2018, 06:11:13 PM
Doc,

Are you just making cuts to full depth with the cutter centred on the gear? (If that makes sense!)

To generate a true involute you'd have to do many cuts rotating the gear slightly each time and raising or lowering the cutter accordingly.

I found a pretty good explanation here http://david.rysdam.org/machining/gears.html (http://david.rysdam.org/machining/gears.html).

He got acceptable results just rotating the gear 1/2 tooth between cuts.

With just one pass he could feel the inaccuracy and the gears wouldn't run when fixed at the theoretical centre distance. With two passes the gears ran together smoothly.

That process would be very easy to automate on a cnc mill with a 4th axis. (Maybe a cnc 4th axis should be another project for you!)

Phil.
Title: Re: Miniature coil winder
Post by: Doc on October 06, 2018, 07:27:50 PM
Using the hob method each pass actually cuts 3 teeth on the gear at different angles. I've used this method before and works like a charm. Yes you probably won't get an absolute perfect gear but you will get a gear dam close and usable.
Title: Re: Miniature coil winder
Post by: awemawson on October 07, 2018, 02:13:41 AM
If the cross sectional form of your cutter is that of a rack of the correct dimensions, and it is long enough to encompass any teeth in mesh then surely by definition it must cut the correct profile.

Obviously the teeth in mesh will vary dependent on the tooth count
Title: Re: Miniature coil winder
Post by: philf on October 07, 2018, 02:53:04 PM
If the cross sectional form of your cutter is that of a rack of the correct dimensions, and it is long enough to encompass any teeth in mesh then surely by definition it must cut the correct profile.

Obviously the teeth in mesh will vary dependent on the tooth count

Not so Andrew!

In a gear planer the cutting rack moves tangentially between strokes and the gear blank rotates a small amount generating the involute form.

With just one pass of a rack form cutter at centre height you get:

(http://listerengine.com/coppermine/albums/userpics/10017/Gearcut1.JPG)

Rotating the blank a tooth (in this case 30 degrees for 12 teeth) you get:

(http://listerengine.com/coppermine/albums/userpics/10017/Gearcut2.JPG)

That's as good as it gets - the involute is approximated with 2 flats.

Add a pass where you rotate the blank 1/2 tooth and raise the cutter the equivalent of 1/2 tooth you get:

(http://listerengine.com/coppermine/albums/userpics/10017/Gearcut3.JPG)

The next pass would be another 1/2 tooth rotation dropping the cutter down to it's original height producing:

(http://listerengine.com/coppermine/albums/userpics/10017/Gearcut4.JPG)

The involute is now approximated with three flats but some horrible looking artefacts at the root of the teeth.

So to generate a perfect involute you'd have to do an infinite number of passes rotating the blank and adjusting the cutter height accordingly. A compromise somewhere in between would give a very acceptable gear.

I chose a 12 tooth gear because this would accentuate the problem.

Hope this makes sense.

Cheers.

Phil.
Title: Re: Miniature coil winder
Post by: awemawson on October 07, 2018, 03:40:07 PM
Makes sense, I'll stick to normal hobs  :thumbup:
Title: Re: Miniature coil winder
Post by: Doc on October 07, 2018, 06:25:32 PM
Yes it is not a perfect tooth profile you end up with 3 small flats on each side of the tooth profile. That being said the profile is plenty good enough for small model engines unless you are building a very high rpm engine. And you need ultra precision gears. I used this process in several motors now and they work just fine. As for the flats after running for some time they are pretty much gone. Unless you spin the gear at the same time as the hob is cutting it is truly not really a hob cutter.
Title: Re: Miniature coil winder
Post by: Doc on October 07, 2018, 09:09:39 PM
Preparing to cut final gear for build. Set up and let machine create the indexing strip.


Title: Re: Miniature coil winder
Post by: Doc on October 08, 2018, 07:34:36 PM
Ok I setup machine and machined the last gear so the gears are completed. Next I'll start on the side plates and spacer block. The gears went pretty good. I'll have to remember to do my index strips like I did this one sure beats laying them out by hand. If I was still working I could have plotted them out on the plotter but the machine came through for me and did it correctly. Any way here is some clips of the last gear getting machined.



Title: Re: Miniature coil winder
Post by: tom osselton on October 08, 2018, 08:58:56 PM
Seems to worked out I was wondering about the mesh because the tape was crooked in places.
Title: Re: Miniature coil winder
Post by: Doc on October 08, 2018, 09:35:57 PM
I think I maybe not to good with the scissors the ends matched up fine when I put it on the indexer. So I'm thinking I cut it a little off. I noticed it when I put it on but the ends lined up so I went forward with it the way it was. Gear looks fine so it didn't effect it to much if at all.
Title: Re: Miniature coil winder
Post by: tom osselton on October 09, 2018, 03:07:54 PM
It should still run in ok.
Title: Re: Miniature coil winder
Post by: Doc on October 15, 2018, 06:52:19 PM
Tested the transmission gear train with a small 12v dc motor. And here are the results.

Title: Re: Miniature coil winder
Post by: tom osselton on October 16, 2018, 02:43:56 PM
Gears seem to have worked out good nice work so far!
Title: Re: Miniature coil winder
Post by: Doc on October 25, 2018, 08:25:41 PM
Thanks Tom
Well getting down to the finish but I did have a error some where. The wire guide I made from a hypodermic needle and some spring steel but ended up to long and would be to close to the spool. So I need to shorten it and I also missed the feed hole in the one side plate.
Once I get those errors fixed I'll get the counter mounted and the motor and I'll be ready for a trial run. 
Title: Re: Miniature coil winder
Post by: Doc on October 31, 2018, 10:02:58 AM
Getting close to the first coil wind and we will see if I end up with a usable coil or not. Always wanted to try this so it will be new to me. I'll need to build a vacuum chamber for it next.

 

=45
Title: Re: Miniature coil winder
Post by: awemawson on October 31, 2018, 12:31:08 PM
George, why can you not just reverse the wires on your speed pot to make it read in the conventional direction ?
Title: Re: Miniature coil winder
Post by: Doc on October 31, 2018, 01:55:43 PM
I may just do that I never gave it a lot of thought but I'm sure that should work.
Thanks  Andrew for waking me up LOL!
Title: Re: Miniature coil winder
Post by: Doc on November 01, 2018, 05:24:40 PM
Pretty much done withe the side winder did fix the control to be standard. Thanks Andrew for waking me up not sure why I did not think of doing that.
 
Made a broach rod for broaching the square hole in the spools. Now on to the vacuum impregnation chamber then I will give it a try.



Title: Re: Miniature coil winder
Post by: Doc on December 21, 2018, 11:17:16 PM
Well getting ready to maybe try and wind a coil up if I can get the ignition stuff done for my Hoglet I'm building.
    I have a plan for the vacuum chamber to impregnate coil with wax. So if I get some time I'll give it a try.
Title: Re: Miniature coil winder
Post by: Doc on January 26, 2019, 10:32:11 PM
Well started winding my first coil I wound the primary which went pretty good and started on secondary (12,500 wraps).
I've got a plan for the vacuum  chamber in mind and going to start as soon as I get the first one wound up.
Title: Re: Miniature coil winder
Post by: Alphawolf45 on January 27, 2019, 02:07:27 PM
Ohh my goodness I own a commercialy mnufatured ccoil winder that is 1/2 as complex.I have use it for making precision resistors for precision circuits in super precise bridge curcits  circa 1950

 It aint entirely that I can speel.. I cqant spell. But also this keyboard double tqps on it's own.I get tired of fixing the spelling mistakes.
Title: Re: Miniature coil winder
Post by: ddmckee54 on January 29, 2019, 12:48:53 PM
I know what you mean about the keyboards.  It seems that there are an awful lot of dyslexic keyboards being manufactured lately.  At least that's the way it feels with my last 3 or 4 keyboards.  The words that get miss-spelled I'VE known how to spell for YEARS!

Don
Title: Re: Miniature coil winder
Post by: Doc on January 31, 2019, 07:32:55 AM
Well did get my first coil done AND IT WORKS. I tested it on 6v and no problems.  I now need to incase it I'm planning on a box a smaller version of a model T  coil. Here is a pic I took from the video.
(https://scontent.ffar1-1.fna.fbcdn.net/v/t1.0-9/50811342_10206136520929266_4577994396582019072_n.jpg?_nc_cat=111&_nc_ht=scontent.ffar1-1.fna&oh=7483470e84dca0706323f1a33582e8c9&oe=5D00B9EE)
Title: Re: Miniature coil winder
Post by: Doc on February 14, 2019, 08:07:20 PM
Here are some pics of the finished coil. It puts out a nice spark at 6V. The primary resistance is 3.0 ohm and the secondary is at 5600 ohms. I'm happy with the way it turned out one more thing I can cross off my would like to build if I could.
Title: Re: Miniature coil winder
Post by: awemawson on February 15, 2019, 02:52:00 AM
Well done Doc.

(Though I'd be nervous of using plywood as the insulator at that sort of voltage)
Title: Re: Miniature coil winder
Post by: tom osselton on February 15, 2019, 02:59:54 PM
Nice work!
Title: Re: Miniature coil winder
Post by: Doc on February 15, 2019, 05:28:33 PM
Thanks Guys.