MadModder

Gallery, Projects and General => Project Logs => Topic started by: doubleboost on May 13, 2013, 06:22:45 PM

Title: Hard Core Three
Post by: doubleboost on May 13, 2013, 06:22:45 PM

Hi
Lads
More video

John

Title: Re: Hard Core Three
Post by: Joules on May 13, 2013, 07:32:56 PM

 :thumbup:   I can empathise with the packing being in the way part way through a job.

Title: Re: Hard Core Three
Post by: andyf on May 13, 2013, 07:44:08 PM

Another great watch, John. Only three expletives, which is pretty good considering you wanted a smoke.

How did you adjust the cutter in the boring bar between cuts, so it would gradually increase the hole diameter?

Andy

Title: Re: Hard Core Three
Post by: Meldonmech on May 14, 2013, 06:29:42 AM

Hi John,

            From time to time we all make little mistakes, but the important thing is how you resolve them, and this is a part of the learning process. In this video this is what you have shown.
                                                                                               Well Done  Cheers David

Title: Re: Hard Core Three
Post by: tekfab on May 14, 2013, 07:47:51 AM

Another great video John. You show it as it is, warts an all !. If you ever fancy a hand building a Mk2 jet kart gimme a shout i've got some kit to hand.

Mike Young

Title: Re: Hard Core Three
Post by: doubleboost on May 14, 2013, 01:42:48 PM

Quote from: andyf on May 13, 2013, 07:44:08 PM

Another great watch, John. Only three expletives, which is pretty good considering you wanted a smoke.

How did you adjust the cutter in the boring bar between cuts, so it would gradually increase the hole diameter?

Andy

Hi
Andy
I should have shown that :Doh: :Doh: :Doh: :Doh:
I use a clock on the cutter and just push the tool  through the required amount
I need to make a proper adjuster

Title: Re: Hard Core Three
Post by: andyf on May 14, 2013, 03:09:09 PM

Quote from: doubleboost on May 14, 2013, 01:42:48 PM

Hi
Andy
I should have shown that :Doh: :Doh: :Doh: :Doh:
I use a clock on the cutter and just push the tool  through the required amount
I need to make a proper adjuster

No, John, I should have thought it out for myself :doh:
 I posted at 00.44 this morning; should have restrained myself until after a night's sleep.

Andy

Title: Re: Hard Core Three
Post by: paulmo101 on May 14, 2013, 03:36:47 PM

Another great video, thanks John.

Did you make the boring bar - if so can you let me have the specs as it looks a good bit of kit?


Cheers

Paul

Title: Re: Hard Core Three
Post by: doubleboost on May 14, 2013, 03:39:15 PM

Hi
Paul
It is shown in the previous video
John

Title: Re: Hard Core Three
Post by: krv3000 on May 14, 2013, 06:21:57 PM

well dun john all bin well i shud be dowing mine this week end

Title: Re: Hard Core Three
Post by: lordedmond on May 15, 2013, 02:53:57 AM

John

when you were stuck with the gland face of the cylinder, could you not have pressed a boring head into service, or at last resort do as i have done in the past when faced with the same problem hold a lathe tool in the four jaw offset to the required rad.

after all its bot the whole face that is critical but only the bolting face.


A point for others its as well to mark the gland bolting face with a couple of discrete pop marks , just so do do not forget which it is  :bang:
the drill lip gauge sure brought back memories I was introduced to those when I started work as an elect apprentice in 1962 we used the lime wash to coat the up stand ( the guys that did the setting out on the marking out slab used it to coat the work to show up the scribe marks ect. )

great vid as always John I think I have pieced up a tip with all of your previous ones

Stuart

ps looking forwards to more

Title: Re: Hard Core Three
Post by: micktoon on May 15, 2013, 05:46:43 AM

Another quality video John  :thumbup: :clap: :clap: , keep them coming , everyone is waiting for the next episode!

Cheers Mick

Title: Re: Hard Core Three
Post by: slowcoach on May 15, 2013, 03:59:31 PM

 :thumbup:  :clap: :clap:

Title: Re: Hard Core Three
Post by: jim4472 on May 16, 2013, 07:07:56 PM

Brilliant Videos  John .. keep em coming ..

how about a video on grinding up centre drills etc for boring bars angles etc.

Jim

Title: Re: Hard Core Three
Post by: paulmo101 on May 17, 2013, 11:18:32 AM

Hi

I would like to second Jims request for a video on grinding broken drills etc for the boring bar or fly cutting.

The videos are great john thnks for the time and effort in making them..

Cheers

Paul