Recent Posts

Pages: 1 [2] 3 4 ... 10
11
Electronics & IC Programing / Re: Pi PICO DRO/Quill-Knee combiner
« Last post by BillTodd on March 21, 2024, 11:01:50 AM »
Hope it is gone for good,


It made a brief return at the weekend - apparently buzzing around my head in a small jet engined vehicle  . I feel ok at the moment.

Quote
We have the 'upgrade for your convenience' of the M27 to look forward to. One of the diversion routes is past our front door.  :hammer:

James
You have my deepest sympathy  -  I know some of the locals had the trucks from Felixstow and Harwich trundling past the home in the early hours when they closed the main road -  It would caused nightmares ... had they been able to sleep.

Luckily I've had the demon to keep me company while the A12 work is progressing - It didn't wake me last-night - I'm hoping the trend continues...

12
Electronics & IC Programing / Re: Pi PICO DRO/Quill-Knee combiner
« Last post by JamesC on March 21, 2024, 07:38:33 AM »
Hope it is gone for good,

We have the 'upgrade for your convenience' of the M27 to look forward to. One of the diversion routes is past our front door.  :hammer:

James
13
Member Videos / powerful metal saw machine
« Last post by celsoari on March 20, 2024, 05:23:21 PM »
After having the channel stopped for a while, I return with a video of a metal sawing machine rescued from scrap metal



i=5mVDQ7pRU1pjmSZt


Greetings from Brazil


Celso Ari
14
How to's / Re: Circlip groove
« Last post by ddmckee54 on March 20, 2024, 11:16:17 AM »
Used carbide drill bits with a 1/8" shank can be had off Ebay for less than a buck a piece.  These can be used to make a variety of small tools, both external tools and internal.
15
How to's / Re: Circlip groove
« Last post by Joules on March 20, 2024, 01:50:23 AM »
Nice insert Bill, that's given me ideas for my own tooling cut from hacksaw blade.  Times like this I wish I had an EDM machine  :thumbup:
16
How to's / Re: Circlip groove
« Last post by BillTodd on March 19, 2024, 06:14:58 PM »
Side on it's triangular with a hole in the middle.

Ideally it needs to sit in a V open at the bottom . It's not difficult to make if you have a mill.
17
How to's / Re: Circlip groove
« Last post by John Rudd on March 19, 2024, 04:54:41 PM »
Bill,
That’s a great gesture….I’ll bear it in mind. Does it need a holder of some sort?

In the meantime, I’ll give some other ideas a go…
18
How to's / Re: Circlip groove
« Last post by BillTodd on March 19, 2024, 03:51:29 PM »
I found a used carbide grooving insert 0.75mm by my measurement.  Might have one good edge, or would sharpen on a diamond lap.

Ph Horn 312.0070.15 1N32

Pm your address and I'll pop in the post
19
How to's / Re: Circlip groove
« Last post by John Rudd on March 19, 2024, 02:31:41 PM »
Just wish the silver steel wasn’t so hard!
20
How to's / Re: Circlip groove
« Last post by Joules on March 19, 2024, 02:16:25 PM »
Sounds like a good approach to getting it sorted.
Pages: 1 [2] 3 4 ... 10