« previous next »
Pages: [1]   Go Down

Author Topic: Cutting my first spur gears  (Read 11865 times)

Offline Joe d

  • Sr. Member
  • ****
  • Posts: 251
  • Country: ca
Cutting my first spur gears
« on: February 06, 2013, 09:44:28 AM »
While this is old stuff to some of you guys, it is a great leap forward for me :beer:

finally cut some spur gears!

Proving that the indexing head works:


came out OK :headbang:


and they even mesh :clap:


No stopping me now!

cheers, Joe
Logged

Offline philf

  • Hero Member
  • *****
  • Posts: 1127
  • Country: gb
Re: Cutting my first spur gears
« Reply #1 on: February 06, 2013, 10:45:33 AM »
Looking good Joe.  :thumbup:

What are you going to use them for?

Phil.
Logged
Phil Fern
Location: Marple, Cheshire

Offline dsquire

  • In Memoriam
  • Hero Member
  • *****
  • Posts: 2275
  • Country: ca
  • Kitchener, Ontario, Canada
Re: Cutting my first spur gears
« Reply #2 on: February 06, 2013, 11:02:05 AM »
Hi Joe

Congratulations on cutting your first set of gears. That wasn't so hard was it. Because it was new made it seem hard. Now that you have that first pair out of the way watch out, Joe is going to give the world a new spin.
 
:D :D

Cheers  :beer:

Don
Logged
Good, better, best.
Never let it rest,
'til your good is better,
and your better best

Offline Joe d

  • Sr. Member
  • ****
  • Posts: 251
  • Country: ca
Re: Cutting my first spur gears
« Reply #3 on: February 06, 2013, 11:19:51 AM »
Thanks guys.

The long term objective (VERY long term) is to put them in a Minnie traction engine.  :dremel:    It's all Rob Wilson's fault. :clap:

Joe
Logged

Offline John Rudd

  • Hero Member
  • *****
  • Posts: 2531
  • Country: gb
Re: Cutting my first spur gears
« Reply #4 on: February 06, 2013, 12:07:28 PM »
Quote from: Joe d on February 06, 2013, 11:19:51 AM
It's all Rob Wilson's fault. :clap:

Joe

Aye that Rob Wilson has a lot to answer for... :lol:

Nice job with the gears Joe  :bow:
Logged
eccentric millionaire financed by 'er indoors
Location:  Backworth Newcastle

Skype: chippiejnr

Offline Pete.

  • Hero Member
  • *****
  • Posts: 1075
  • Country: gb
Re: Cutting my first spur gears
« Reply #5 on: February 06, 2013, 02:45:12 PM »
Nice job. I have only made a few gears but I remember the first one well - I was bricking it the whole way :D
Logged

Offline sparky961

  • Hero Member
  • *****
  • Posts: 844
  • Country: ca
Re: Cutting my first spur gears
« Reply #6 on: February 06, 2013, 03:54:34 PM »
Looks good!  I've made a few myself, but I've never had the luxury of a profile cutter.  I've always had to grind a tool and fit things the best I can.  It would probably sound better with the gear cutter over a single point tool as well... ;)

-Sparky
Logged

Rob.Wilson

  • Guest
Re: Cutting my first spur gears
« Reply #7 on: February 07, 2013, 01:52:31 PM »
 :lol: :lol: :lol: Nice going Joe ,,,,,,, just few more gears to do  :poke:

Your dividing attachment looks cracking  :bow: :bow: :bow: :bow: lovely bit of kit  :thumbup:


Rob
Logged

Offline Joe d

  • Sr. Member
  • ****
  • Posts: 251
  • Country: ca
Re: Cutting my first spur gears
« Reply #8 on: February 09, 2013, 08:53:11 PM »

Thanks again guys.


Quote from: RobWilson on February 07, 2013, 01:52:31 PM
just few more gears to do  :poke:Rob

Jeeze Rob.... give a man time to breath....  and since we're poking  :poke:  how's YOUR traction engine coming along? :lol: :lol:

Thanks for noticing the dividing head, happy to say that it works as it should.

Now, since you hinted so nicely, here you go!


The last one to go is 80 teeth on the blank you see there, and then all done for the Minnie (as far as spur gears are concerned)
(Of course, NOTHING ELSE is done yet... had to start somewhere :) )
Logged

Rob.Wilson

  • Guest
Re: Cutting my first spur gears
« Reply #9 on: February 10, 2013, 04:25:52 AM »
Hi Joe

Now thats a dam fine set of gears you have cut   :clap: :clap: :clap: nicely done  :thumbup:



Quote
Jeeze Rob.... give a man time to breath....  and since we're poking    how's YOUR traction engine coming along?

 :lol: :lol: :lol: :lol:  its not  :Doh:  way too many distractions  :proj:


Rob







Logged
Pages: [1]   Go Up
« previous next »