« previous next »
Pages: [1]   Go Down

Author Topic: STEEL BOILER  (Read 10683 times)

Offline doubleboost

  • Madmodder Committee
  • Hero Member
  • *****
  • Posts: 1619
  • Country: gb
  • Newcastle Upon Tyne
STEEL BOILER
« on: May 20, 2008, 05:11:37 PM »
Hi
I am buisy building a steel boiler for a marine engine
The boiler shell is 8 inch diamiter 22 inches long 8 mm wall thickness
The tube plates are 10 mm thick 19 - 1 inch tubes
I have a 140 amp TIG inverter and a migatronic 160 amp MIG
Would it be best to put in a TIG root weld then run MIG in to the joints or just tig weld the whole thing
The working pressure will be 125 psi

boiler end plate counter sunk


1 1/2 bsp wash out plug TIG welded inside and out
Regards
John
Logged

Offline Brass_Machine

  • Administrator
  • Hero Member
  • *****
  • Posts: 5534
  • Country: us
Re: STEEL BOILER
« Reply #1 on: May 20, 2008, 10:41:10 PM »
Nice work so far. I really don't have an answer for you as my knowledge of welding is very limited. Personally I would TIG it. But you may want to hop over to Welderzone and ask there. Being a boiler, I would be very careful.

Eric
Logged
Science is fun.

We're all mad here. I'm mad. You're mad.

Offline PTsideshow

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 2570
  • Country: us
Re: STEEL BOILER
« Reply #2 on: May 21, 2008, 06:39:04 AM »
Very nice work on the plug, I to would have to say that if you are doing that nice of TIG, why do any other. On a side note, you can all ways take some scrap material you are using for the boiler. Prep it and weld it then cut it thru the weld to check out your penetration etc.
I posted some links for a boiler code and another forum with boiler info on it. Here in the resources section
http://madmodder.net/Forum/index.php?topic=200.new#new
 ;D
Logged
"The internet just a figment, of my imagination!' 
 
 There are only 3 things I can't do!"
Raise the Dead!
        Walk on water!
                 Fix a broken heart!
and I'm working on the first two!
glen

Offline doubleboost

  • Madmodder Committee
  • Hero Member
  • *****
  • Posts: 1619
  • Country: gb
  • Newcastle Upon Tyne
Re: STEEL BOILER
« Reply #3 on: June 25, 2008, 07:04:25 PM »
Hi
Did some more to the boiler today decided to tig the whole job

first run (root weld) 140 amp


I ground a champher on the plate 3/4 its depth the weld went all the way through
Regards
John
Logged

Offline PTsideshow

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 2570
  • Country: us
Re: STEEL BOILER
« Reply #4 on: June 25, 2008, 08:17:19 PM »
Looking good smart chose! ;D
Logged
"The internet just a figment, of my imagination!' 
 
 There are only 3 things I can't do!"
Raise the Dead!
        Walk on water!
                 Fix a broken heart!
and I'm working on the first two!
glen

Offline Bernd

  • Madmodder Committee
  • Hero Member
  • *****
  • Posts: 3688
  • Country: us
  • 1915 C Cab
    • Kingstone Model Works
Re: STEEL BOILER
« Reply #5 on: June 25, 2008, 08:55:05 PM »
Nice job on those welds.

Bernd
Logged
Route of the Black Diamonds

Offline Brass_Machine

  • Administrator
  • Hero Member
  • *****
  • Posts: 5534
  • Country: us
Re: STEEL BOILER
« Reply #6 on: June 27, 2008, 11:46:32 AM »
Hey John!

That is looking very nice.The welds have that nice stacked dime look. Very nice.

Keep the pictures coming

Eric
Logged
Science is fun.

We're all mad here. I'm mad. You're mad.

Offline doubleboost

  • Madmodder Committee
  • Hero Member
  • *****
  • Posts: 1619
  • Country: gb
  • Newcastle Upon Tyne
Re: STEEL BOILER
« Reply #7 on: June 27, 2008, 05:52:19 PM »
Hi
My tig welder is lacking in power to put the fillet welds on the tube plates
I used some 3.5 super chrome rods at 110 amps pleased with the results not as pritty as tig but really strong with good penitration


This is my tig inverter it runs mma great
Logged

Offline Powder Keg

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 932
  • Country: us
  • Machinist Extraordinaire
Re: STEEL BOILER
« Reply #8 on: July 24, 2008, 09:31:35 PM »
Looking great!!! What are the tubes going to be made out of? Copper?

Thanks for sharing, Wes
Logged
Wesley P
A Gismo ??? If it has a flywheel or spins and is made with small parts. I'll take one! If it makes noise, moves, or requires frequent oiling and dusting it's a better deal yet. It's especially right if its shiny and bright; but if it's dirty and dull it wont mater at all...

Circlip

  • Guest
Re: STEEL BOILER
« Reply #9 on: November 30, 2008, 02:40:15 PM »
Looks impressive John, is it a standard design and did you keep the material and coding certs for when the boiler inspector tests it for insurance purposes. ?

 Regards  Ian.
Logged

Offline Darren

  • Madmodder Committee
  • Hero Member
  • *****
  • Posts: 3795
  • N/Wales
Re: STEEL BOILER
« Reply #10 on: December 09, 2008, 04:51:41 PM »
John, if that was my welding I'd be very pleased with myself.....looks great... :wave:
Logged
You will find it a distinct help… if you know and look as if you know what you are doing. (IRS training manual)

Offline doubleboost

  • Madmodder Committee
  • Hero Member
  • *****
  • Posts: 1619
  • Country: gb
  • Newcastle Upon Tyne
Re: STEEL BOILER
« Reply #11 on: October 01, 2011, 03:12:38 PM »
Hi
This is a post from some time ago
The boiler has been standing in the shop with a bench grinder fastend to it for a couple of years now
Decided to sort out a boiler for my engine
After a cold start i had 90 psi within 20 minutes
I need a water guage and a feed pump making



John
Logged
Pages: [1]   Go Up
« previous next »