| The Shop > CNC |
| DDCSV1.1 4 Axis controller |
| << < (169/202) > >> |
| WeldingRod:
--- Quote from: dale brisson on January 23, 2018, 03:40:53 PM --- --- Quote from: dale brisson on January 23, 2018, 01:27:55 PM ---anyone got the 4th axis running? i dont know how to figure it all out.looking for info driver is set to 1600 200 steps on motor 6:1 gearing how do i set pulse/degree and is there anything else i have to change in the ddcsv? :bang: --- End quote --- never mind got it when setting the pulse ddcsv will not allow you to go under 00050.00 so had to up the driver microsteps --- End quote --- Pandora fixed this, or I can tell you how to do it manually. Sent from my SAMSUNG-SM-G891A using Tapatalk |
| dale brisson:
please tell me PLEASE also is the 4th axis work with all others axis or does it replace x/y axis as a wrapped job so say my 4th is on my y will my y still run or all at the same time? i hope i asked this right |
| WeldingRod:
--- Quote from: dale brisson on January 23, 2018, 04:20:35 PM ---please tell me PLEASE also is the 4th axis work with all others axis or does it replace x/y axis as a wrapped job so say my 4th is on my y will my y still run or all at the same time? i hope i asked this right --- End quote --- As long as you have the 4 axis version, you have 4 completely separate motion controls. I have verified that I can get simultaneous , coordinated motion on all four axies. Sent from my SAMSUNG-SM-G891A using Tapatalk |
| dale brisson:
--- Quote from: WeldingRod on January 23, 2018, 05:33:06 PM --- --- Quote from: dale brisson on January 23, 2018, 04:20:35 PM ---please tell me PLEASE also is the 4th axis work with all others axis or does it replace x/y axis as a wrapped job so say my 4th is on my y will my y still run or all at the same time? i hope i asked this right --- End quote --- As long as you have the 4 axis version, you have 4 completely separate motion controls. I have verified that I can get simultaneous , coordinated motion on all four axies. Sent from my SAMSUNG-SM-G891A using Tapatalk --- End quote --- im playing around with the cam side right now looking around on what to use . as i have a few different softwares. on thing i really wish this unit had was a better probe functions or some sort of auto z where it can adjust the height to the workpiece i know grbl can and estlcam but will not work with the ddcsv .. i might end up going with massco all in one |
| WeldingRod:
--- Quote from: dale brisson on January 23, 2018, 05:37:16 PM --- --- Quote from: WeldingRod on January 23, 2018, 05:33:06 PM --- --- Quote from: dale brisson on January 23, 2018, 04:20:35 PM ---please tell me PLEASE also is the 4th axis work with all others axis or does it replace x/y axis as a wrapped job so say my 4th is on my y will my y still run or all at the same time? i hope i asked this right --- End quote --- As long as you have the 4 axis version, you have 4 completely separate motion controls. I have verified that I can get simultaneous , coordinated motion on all four axies. Sent from my SAMSUNG-SM-G891A using Tapatalk --- End quote --- im playing around with the cam side right now looking around on what to use . as i have a few different softwares. on thing i really wish this unit had was a better probe functions or some sort of auto z where it can adjust the height to the workpiece i know grbl can and estlcam but will not work with the ddcsv .. i might end up going with massco all in one --- End quote --- Probing DOES work, btw. I tried it today for the first time. Sent from my SAMSUNG-SM-G891A using Tapatalk |
| Navigation |
| Message Index |
| Next page |
| Previous page |