DDCSV1.1 4 Axis controller

The Shop > CNC

<< < (120/202) > >>

Benedikt:
The Chinese as well as most of Europe prefers millimeters. I doubt the Chinese who initially developed the firmware really cared about inch support.
Eventually, I may officially add inches to the new firmware.

Also, I just like to make it clear once again. The configurator has moved to http://config.pandora-cnc.eu/ and the downloads are now available from http://pandora-cnc.eu/download
There is now also an installation guide in two languages:
English: http://docs.pandora-cnc.eu/en/getting-started
German: http://docs.pandora-cnc.eu/de/getting-started

EDIT: In the documentation, the arrows are broken. You'll need to use the sidebar until this is resolved.
Also, the documentation is very short. If anyone would like to write a few pages (especially on general usage), that would be great.

BR,
Benedikt

PPRINT:
Benedikt, thanks once again for all of the great support on this project. I know I am really excited about the work you are doing.

Andy, "...feed codes are working"? I'm not following.

Rob

Sent from my SAMSUNG-SM-G900A using Tapatalk

aolney:
Rob -
I thought the feedrate shown in the display did not match the feedrate given in the gcode ie G01 X1 F40, but i ran it again and it seem to work.
Andy

riorao:

--- Quote from: Benedikt M. on May 24, 2017, 01:51:27 PM ---The Chinese as well as most of Europe prefers millimeters. I doubt the Chinese who initially developed the firmware really cared about inch support.
Eventually, I may officially add inches to the new firmware.

Also, I just like to make it clear once again. The configurator has moved to http://config.pandora-cnc.eu/ and the downloads are now available from http://pandora-cnc.eu/download
There is now also an installation guide in two languages:
English: http://docs.pandora-cnc.eu/en/getting-started
German: http://docs.pandora-cnc.eu/de/getting-started

EDIT: In the documentation, the arrows are broken. You'll need to use the sidebar until this is resolved.
Also, the documentation is very short. If anyone would like to write a few pages (especially on general usage), that would be great.

BR,
Benedikt

--- End quote ---

I want to make the interface translation into Russian.
Found in the firmware two files in /upgrade/nand - CHS and ENG
You can add a third file RUS in the utf-8?

Benedikt:

--- Quote from: riorao on May 29, 2017, 12:53:19 AM ---
--- Quote from: Benedikt M. on May 24, 2017, 01:51:27 PM ---The Chinese as well as most of Europe prefers millimeters. I doubt the Chinese who initially developed the firmware really cared about inch support.
Eventually, I may officially add inches to the new firmware.

Also, I just like to make it clear once again. The configurator has moved to http://config.pandora-cnc.eu/ and the downloads are now available from http://pandora-cnc.eu/download
There is now also an installation guide in two languages:
English: http://docs.pandora-cnc.eu/en/getting-started
German: http://docs.pandora-cnc.eu/de/getting-started

EDIT: In the documentation, the arrows are broken. You'll need to use the sidebar until this is resolved.
Also, the documentation is very short. If anyone would like to write a few pages (especially on general usage), that would be great.

BR,
Benedikt

--- End quote ---

I want to make the interface translation into Russian.
Found in the firmware two files in /upgrade/nand - CHS and ENG
You can add a third file RUS in the utf-8?

--- End quote ---
Unfortunately I do not speak any Russian. But since you do so, if you translate the English text that I can send you via email to Russian, I will make Russian a language option with the next firmware release and also add it to the configurator as a language option.
I will add a German file too. If someone would also translate the text into French or Italian or any other language, I will surely also include these languages. There is a bit of code to add and a lot of patching to do. But I guess I can make it work for you ;)

Navigation

 Message Index

Go to full version