Gallery, Projects and General > Project Logs
Elmers #25, my first engine project
Bernd:
Tim,
I think you've been telling us porkies. No newbie can single point a small thread like that and get away with it the first time around. :lol:
I think your either not a newbie or you've got natrual talent. I think the later may be it.
Looks like you got a good finish with that boring bar. Keep it up and you'll be running with the best of them. :clap:
Bernd
spuddevans:
--- Quote from: Bernd on May 11, 2009, 03:57:56 PM ---Tim,
I think you've been telling us porkies. No newbie can single point a small thread like that and get away with it the first time around. :lol:
--- End quote ---
Well I did show you just one pic of my first project, ( I gotta take some more pics of them ) the 6 Led lights? They all are made up of a 2 piece construction that are threaded together. That is where I learnt a lot about single point threading, also where I made quite a few mistakes too. ( there's a few verry loose threads on a couple )
But the threading on this was a lot easier as I was just copying a M3 screw and I had a M3 nut on hand to be able to stop and check if I was close. I just started out by measuring the diameter of the M3 scerw threaded portion, turning the brass pin down to match, changed to the threading bit, engaged the half-nuts and threaded it 0.05mm at a pass until the nut would screw on to the brass pivot pin.
It's a bit easier when you have something to copy.
Tim
spuddevans:
I managed to sneak a couple more hours in the playroom workshop this afternoon.
I started off by off a little lump of brass for the piston and chucking in the 4jaw, turned down half to diameter.
I then chucked it the other way round in the ER32 collet but made the error of not tightening it enough and it came loose just as I was parting it off to length :bang: :bang:
So I added to my collection of spare "smaller than I wanted" pieces and hacked off another lump of brass, chucked it and turned it down as before. This time I also drilled and tapped M3
I find this to be a good method of tapping on the lathe, to explain; The drill chuck is not jammed in the MT of the tailstock, it has some grip but is free to turn with light pressure. Also the tailstock is also free to move on the ways, and the tap in the chuck is also loose enough to turn if the tap jams in the work. I then run the lathe at a very low speed.
So that's all I got done today, just 2 pistons made, 1 junked and one that fits ok. If I put a M3 screw in the piston and slide it into the cylinder and turn it upside down the piston gently slides down and stops at the entrance of the cylinder, with out the screw it just falls out. I dont know if it's too loose, if I pull the piston out rapidly I get a satisfying "pop".
How do you tell if the piston is too loose or not?
Things I've learnt today;
I learnt that my ER32 chuck has a runout of 0.02mm, is that bad?
Always start off with a piece of metal that is longer than you need as it makes life easier.
I also tried making a con-rod out of 303 stainless, it didnt go quite as planned but I learnt that it really helps to use sharp carbide tooling and that it doesn't like my Hss threading tool.(prob was a bit dull, I must resharpen it) I'll try again the next time with some brass as per the plans.
Also learnt to think a few steps ahead to see what I can do while workpiece is still chucked and true before taking the piece out and then spending 15mins truing it up with the trusty dial indicator.
And finally, always remember to check that whatever chucking device is used is properly tightened up.
Tim
Darren:
Excellent work again there Tim, :thumbup:
I like to turn SS fast, very fast and with fast feed, but only with tungsten tipped cutters.
If you are using HSS tooling then keep the speed down low or you'll just burn the tip opp the cutting tool.
Nice clear pictures btw, :nrocks:
Brass_Machine:
... I dont know if it's too loose, if I pull the piston out rapidly I get a satisfying "pop".
How do you tell if the piston is too loose or not?
[/quote]
That sounds good to me. If it was too loose, you wouldn't get the "pop"
Eric
Navigation
[0] Message Index
[#] Next page
[*] Previous page
Go to full version