« previous next »
Pages: 1 [2]  All   Go Down

Author Topic: Fan removal  (Read 25240 times)

RobWilson

  • Guest
Re: Fan removal
« Reply #25 on: April 10, 2016, 12:20:20 PM »
 :scratch: Blades look straight to me mate , just off set  :smart:



Rob
Logged

RobWilson

  • Guest
Re: Fan removal
« Reply #26 on: April 10, 2016, 12:42:17 PM »
Something like this John












Rob
Logged

Offline Fergus OMore

  • Hero Member
  • *****
  • Posts: 1012
  • Country: england
Re: Fan removal
« Reply #27 on: April 11, 2016, 04:48:01 AM »
I used to burn out the things way back. Probably in the 1950's or early 60's.

As far as I recall 'replacements' were a complete cartridge but minus the fan.  I got mine from Tyne Tees Power Tool Co in Heaton Road in Byker. The place is still there! All that we did was to prise off the fan, put it on the new cartridge and put it all back-- to burn out again!.

I suppose the prising off was done with nothing more than a couple of screwdrivers- in the back shop.

Thanks for the memory

Norman
Logged

RobWilson

  • Guest
Re: Fan removal
« Reply #28 on: May 04, 2016, 01:32:55 PM »
Well Mr Rudd  :poke:   ,,,,,,,IS IT DONE YET ! it's been months  :coffee:


Rob
« Last Edit: May 04, 2016, 01:58:47 PM by RobWilson »
Logged

Offline John Rudd

  • Hero Member
  • *****
  • Posts: 2531
  • Country: gb
Re: Fan removal
« Reply #29 on: May 04, 2016, 02:34:16 PM »
In a word NO...... :lol:

I had some 10 mm flat bar delivered today, so should make some progress...I need to make something like 5 new fans....
I've now got a bit of a collection of Stanley Bridges drills dating from the very early 60's thru' to mid - 70's....a total of around 15-17 drills.....its become a bit of an obsession really.... :drool:
Logged
eccentric millionaire financed by 'er indoors
Location:  Backworth Newcastle

Skype: chippiejnr

Offline awemawson

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 9015
  • Country: gb
  • East Sussex, UK
Re: Fan removal
« Reply #30 on: May 04, 2016, 02:49:58 PM »
Time for a 3D printer perhaps  :clap:
Logged
Andrew Mawson
East Sussex

Offline John Rudd

  • Hero Member
  • *****
  • Posts: 2531
  • Country: gb
Re: Fan removal
« Reply #31 on: May 04, 2016, 04:25:37 PM »
Quote from: awemawson on May 04, 2016, 02:49:58 PM
Time for a 3D printer perhaps  :clap:

Errr.....NO........I dont need any more toys, repeat, I dont need any more toys.....Oh ok....good idea... :lol:
Logged
eccentric millionaire financed by 'er indoors
Location:  Backworth Newcastle

Skype: chippiejnr

Offline John Rudd

  • Hero Member
  • *****
  • Posts: 2531
  • Country: gb
Re: Fan removal
« Reply #32 on: May 21, 2016, 07:30:22 AM »
Quote from: RobWilson on May 04, 2016, 01:32:55 PM
Well Mr Rudd  :poke:   ,,,,,,,IS IT DONE YET ! it's been months  :coffee:


Rob
Some progress made today......
I now need to mount the disc on a mandrel, put it on the rotab and mill the fins....then job done .
I hope...
Logged
eccentric millionaire financed by 'er indoors
Location:  Backworth Newcastle

Skype: chippiejnr

RobWilson

  • Guest
Re: Fan removal
« Reply #33 on: May 22, 2016, 03:25:16 AM »
Looking good John  :thumbup:

Congrats on your wedding anniversary  :beer:


Rob 
Logged

Offline John Rudd

  • Hero Member
  • *****
  • Posts: 2531
  • Country: gb
Re: Fan removal- proof of concept
« Reply #34 on: May 23, 2016, 08:15:35 AM »
Thanks Rob, had a great time at the pictures on the Wednesday....( I dont kiss and tell.... :lol:)

So, abandoned the idea of making a new fan from ally, coz it hurt my cutters too much....
So after Andrew's comments about a printed version,......hang on a minute....I got some acrylic sheet somewhere....

Well after an hour I got this made.....

I'm not sure about its durability, will it survive spinning at 4-5000 rpm?
Who knows....?
Logged
eccentric millionaire financed by 'er indoors
Location:  Backworth Newcastle

Skype: chippiejnr

Offline Joules

  • Hero Member
  • *****
  • Posts: 1278
  • Country: gb
Re: Fan removal
« Reply #35 on: May 23, 2016, 10:36:22 AM »
Someone mention 3D printing ?   I just happen to have .............
Logged
Honour your mentors, and pay it forward.
Pages: 1 [2]  All   Go Up
« previous next »