&& #5 -t1 -s1"minimum log radius of 4axis machining" -s2"mm" -m1 -min=3.000 -max=999.999 #6 -t2 -s1"A axis rotate reference axis" -m1 -min=0.000 -max=3.000 -i0"X axis" -i1"Y axis" -i2"Z axis" -i3"not rotate" #104 -t2 -s1"A axis optimal path when G0 run" -m1 -min=0.000 -max=1.000 -i0"No" -i1"Yes" #34 -t1 -s1"X axis pulse equivalency" -s2"pulse/mm" -m2 -min=50.000 -max=99999.000 #35 -t1 -s1"Y axis pulse equivalency" -s2"pulse/mm" -m2 -min=50.000 -max=99999.000 #36 -t1 -s1"Z axis pulse equivalency" -s2"pulse/mm" -m2 -min=50.000 -max=99999.000 #37 -m0 #38 -t1 -s1"A axis pulse equivalency" -s2"" -m2 -min=50.000 -max=999999.000 #39 -t2 -s1"A axis pulse unit" -m2 -min=0.000 -max=1.000 -i0"pulse/deg" -i1"pulse/circle" #40 -t2 -s1"AB axis Selection" -m2 -min=0.000 -max=1.000 -i0"A axis" -i1"B axis" #390 -t2 -s1"X axis DIR signal Electric Level" -m2 -min=0.000 -max=1.000 -i0"Low" -i1"High" #391 -t2 -s1"Y axis DIR signal Electric Level" -m2 -min=0.000 -max=1.000 -i0"Low" -i1"High" #392 -t2 -s1"Z axis DIR signal Electric Level" -m2 -min=0.000 -max=1.000 -i0"Low" -i1"High" #393 -t2 -s1"A axis DIR signal Electric Level" -m2 -min=0.000 -max=1.000 -i0"Low" -i1"High" #418 -t2 -s1"X axis Pulse signal Electric Level" -m2 -min=0.000 -max=1.000 -i0"Low" -i1"High" #419 -t2 -s1"Y axis Pulse signal Electric Level" -m2 -min=0.000 -max=1.000 -i0"Low" -i1"High" #420 -t2 -s1"Z axis Pulse signal Electric Level" -m2 -min=0.000 -max=1.000 -i0"Low" -i1"High" #421 -t2 -s1"A axis Pulse signal Electric Level" -m2 -min=0.000 -max=1.000 -i0"Low" -i1"High" #416 -t0 -s1"Time interval between DIR & pulse" -s2"ns" -m2 -min=0.000 -max=9999.000 #33 -t1 -s1"Motor start speed" -s2"mm/min" -m2 -min=0.000 -max=999.000 #100 -t1 -s1"X axis manual control speed" -s2"mm/min" -m3 -min=99.000 -max=99999.000 #101 -t1 -s1"Y axis manual control speed" -s2"mm/min" -m3 -min=99.000 -max=99999.000 #102 -t1 -s1"Z axis manual control speed" -s2"mm/min" -m3 -min=99.000 -max=99999.000 #103 -t1 -s1"A axis manual control speed" -s2"deg/min" -m3 -min=99.000 -max=99999.000 #41 -t1 -s1"X Axis max speed in M_Ctrl mode" -s2"mm/min" -m3 -min=99.000 -max=99999.000 #42 -t1 -s1"Y Axis max speed in M_Ctrl mode" -s2"mm/min" -m3 -min=99.000 -max=99999.000 #43 -t1 -s1"Z Axis max speed in M_Ctrl mode" -s2"mm/min" -m3 -min=99.000 -max=99999.000 #44 -t1 -s1"A Axis max speed in M_Ctrl mode" -s2"deg/min" -m3 -min=99.000 -max=99999.000 #45 -t1 -s1"X axis start Acc in M_Ctrl mode" -s2"mm/s2" -m3 -min=9.000 -max=9999.000 #46 -t1 -s1"Y axis start Acc in M_Ctrl mode" -s2"mm/s2" -m3 -min=9.000 -max=9999.000 #47 -t1 -s1"Z axis start Acc in M_Ctrl mode" -s2"mm/s2" -m3 -min=9.000 -max=9999.000 #48 -t1 -s1"A axis start Acc in M_Ctrl mode" -s2"deg/s2" -m3 -min=9.000 -max=9999.000 #263 -t1 -s1"X axis stop Acc in M_Ctrl mode" -s2"mm/s2" -m3 -min=9.000 -max=9999.000 #264 -t1 -s1"Y axis stop Acc in M_Ctrl mode" -s2"mm/s2" -m3 -min=9.000 -max=9999.000 #265 -t1 -s1"Z axis stop Acc in M_Ctrl mode" -s2"mm/s2" -m3 -min=9.000 -max=9999.000 #266 -t1 -s1"A axis stop Acc in M_Ctrl mode" -s2"deg/s2" -m3 -min=9.000 -max=9999.000 #15 -t2 -s1"Speed Selection" -s3"0:set by G code,1:use default speed" -m4 -min=0.000 -max=1.000 -i0"G code" -i1"default" #76 -t1 -s1"default operation speed" -s2"mm/min" -m4 -min=10.000 -max=99999.000 #99 -t1 -s1"operation acceleration" -s2"mm/s2" -m4 -min=9.000 -max=9999.000 #80 -t1 -s1"G0 Speed" -s2"mm/min" -m4 -min=99.000 -max=99999.000 #77 -t1 -s1"maximum speed" -s2"mm/min" -m4 -min=99.000 -max=99999.000 #78 -t1 -s1"Z axis lifting protection speed" -s2"mm/min" -m4 -min=99.000 -max=99999.000 #79 -t1 -s1"Z axis dropping protection speed" -m4 -min=99.000 -max=99999.000 #435 -t1 -s1"X axis protection speed" -s2"mm/min" -m4 -min=99.000 -max=99999.000 #436 -t1 -s1"Y axis protection speed" -s2"mm/min" -m4 -min=99.000 -max=99999.000 #82 -t1 -s1"Z axis safe height" -s2"mm" -m4 -min=0.000 -max=99.000 #89 -t1 -s1"Z axis back distance when pause" -s2"mm" -m4 -min=0.000 -max=99.000 #395=1 -t2 -s1"support of G53 coordinate sys" -s3"0:support,1:not support" -m0 -min=0.000 -max=1.000 -i0"Yes" -i1"No" #16 -t2 -s1"current coordinate system" -s3"0:G53,1:G54,2:G55,3:G56,4:G57,5:G58,6:G59,7:MACH" -m5 -min=1.000 -max=7.000 -i0"G53" -i1"G54" -i2"G55" -i3"G56" -i4"G57" -i5"G58" -i6"G59" -i7"MACH" #219 -t2 -s1"If Stop Spindle when pause" -m6 -min=0.000 -max=1.000 -i0"No" -i1"Yes" #220 -t2 -s1"Spindle speed selection" -s3"0:set by G code,1:default speed of spindle" -m6 -min=0.000 -max=1.000 -i0"G code" -i1"default" #221 -t1 -s1"default spindle speed" -s2"rpm" -m6 -min=10.000 -max=99999.000 #98 -t1 -s1"maximum spindle speed" -s2"rpm" -m6 -min=99.000 -max=99999.000 #227 -t2 -s1"Spindle switch Active level" -m6 -min=0.000 -max=1.000 -i0"Low" -i1"High" #422 -t2 -s1"definition of PWM Electric level" -m6 -min=0.000 -max=1.000 -i0"Low" -i1"High" #222 -t2 -s1"Spindle commands M3/M5 response" -s3"0:not response,1:response" -m6 -min=0.000 -max=1.000 -i0"No" -i1"Yes" #224 -t1 -s1"Spindle M3/M4/M5 response Duration" -s2"s" -m6 -min=0.000 -max=9.000 #433 -t0 -s1"PWM rising rate from 0V to 10V" -m6 -min=0.000 -max=65535.000 #108 -t2 -s1 "M Bus IO command response" -s3"0:not response,1:response" -m7 -min=0.000 -max=1.000 -i0"No" -i1"Yes" #109 -t0 -s1 "M Bus IO default status" -m7 -min=0 -max=4294967295 #228 -t2 -s1"M8/M9 active electric level" -m7 -min=0.000 -max=1.000 -i0"Low" -i1"High" #229 -t2 -s1"M10/M11 active electric level" -m7 -min=0.000 -max=1.000 -i0"Low" -i1"High" #223 -t2 -s1"response of M code(M8/M9,M10/M11)" -s3"0:not response,1:response" -m7 -min=0.000 -max=1.000 -i0"No" -i1"Yes" #225 -t1 -s1"delay time of M8/M9" -s2"s" -m7 -min=0.000 -max=9.000 #226 -t1 -s1"delay time of M10/M11" -s2"s" -m7 -min=0.000 -max=9.000 #49 -t0 -s1"HOME times" -m8 -min=1.000 -max=5.000 #50 -t2 -s1"HOME signal Effective when HOME" -m8 -min=0.000 -max=1.000 -i0"Ignore HOME" -i1"Continue HOME" #51 -t2 -s1"Enable limit signal when HOME" -s3"0:Disable,1:Enable" -m8 -min=0.000 -max=1.000 -i0"Disable" -i1"Enable" #52 -t2 -s1"Enable X Home Searching function" -s3"0:not enable,1:enable" -m8 -min=0.000 -max=1.000 -i0"Disable" -i1"Enable" #53 -t2 -s1"Enable Y Home Searching function" -s3"0:not enable,1:enable" -m8 -min=0.000 -max=1.000 -i0"Disable" -i1"Enable" #54 -t2 -s1"Enable Z Home Searching function" -s3"0:not enable,1:enable" -m8 -min=0.000 -max=1.000 -i0"Disable" -i1"Enable" #55 -t2 -s1"Enable Z Home Searching function" -s3"0:not enable,1:enable" -m8 -min=0.000 -max=1.000 -i0"Disable" -i1"Enable" #60 -t2 -s1"X axis Home signal Electric Level" -m8 -min=0.000 -max=1.000 -i0"Low" -i1"High" #61 -t2 -s1"Y axis Home signal Electric Level" -m8 -min=0.000 -max=1.000 -i0"Low" -i1"High" #62 -t2 -s1"Z axis Home signal Electric Level" -m8 -min=0.000 -max=1.000 -i0"Low" -i1"High" #63 -t2 -s1"A axis Home signal Electric Level" -m8 -min=0.000 -max=1.000 -i0"Low" -i1"High" #64 -t2 -s1"X axis Home direction" -m8 -min=0.000 -max=1.000 -i0"Negative" -i1"Positive" #65 -t2 -s1"Y axis Home direction" -m8 -min=0.000 -max=1.000 -i0"Negative" -i1"Positive" #66 -t2 -s1"Z axis Home direction" -m8 -min=0.000 -max=1.000 -i0"Negative" -i1"Positive" #67 -t2 -s1"A axis Home direction" -m8 -min=0.000 -max=1.000 -i0"Negative" -i1"Positive" #56 -t1 -s1"X axis Home speed" -s2"mm/min" -m8 -min=99.000 -max=99999.000 #57 -t1 -s1"Y axis Home speed" -s2"mm/min" -m8 -min=99.000 -max=99999.000 #58 -t1 -s1"Z axis Home speed" -s2"mm/min" -m8 -min=99.000 -max=99999.000 #59 -t1 -s1"A axis Home speed" -s2"deg/min" -m8 -min=99.000 -max=99999.000 #83 -t1 -s1"X axis back distance after Home" -s2"mm" -m8 -min=0.000 -max=99.000 #84 -t1 -s1"Y axis back distance after Home" -s2"mm" -m8 -min=0.000 -max=99.000 #85 -t1 -s1"Z axis back distance after Home" -s2"mm" -m8 -min=0.000 -max=99.000 #86 -t1 -s1"A axis back distance after Home" -s2"deg" -m8 -min=0.000 -max=360.000 #68 -t2 -s1"Tool Setting function mode " -m9 -min=0.000 -max=2.000 -i0"Disable" -i1"mode 1" -i2"mode 2" #70 -t2 -s1"Probe signal electric level" -m9 -min=0.000 -max=1.000 -i0"Low" -i1"High" #69 -t1 -s1"Thickness of tool sensor" -s2"mm" -m9 -min=-99.000 -max=99.000 #71 -t2 -s1"Initial tool's position" -m9 -min=0.000 -max=1.000 -i0"current position" -i1"fixed position" #72 -t1 -s1"Initial probe position on X axis" -s2"mm" -m9 -min=-9999.000 -max=9999.000 #73 -t1 -s1"Initial probe position on Y axis" -s2"mm" -m9 -min=-9999.000 -max=9999.000 #74 -t1 -s1"Initial probe position on Z axis" -s2"mm" -m9 -min=-9999.000 -max=9999.000 #75 -t1 -s1"back distance after probe" -s2"mm" -m9 -min=0.000 -max=99.000 #400 -t2 -s1"Limited siganl active of X--" -s3"0:not enable,1:enable" -m10 -min=0.000 -max=1.000 -i0"Disable" -i1"Enable" #401 -t2 -s1"Limited siganl active of Y--" -s3"0:not enable,1:enable" -m10 -min=0.000 -max=1.000 -i0"Disable" -i1"Enable" #402 -t2 -s1"Limited siganl active of Z--" -s3"0:not enable,1:enable" -m10 -min=0.000 -max=1.000 -i0"Disable" -i1"Enable" #403 -t2 -s1"Limited siganl active of A--" -s3"0:not enable,1:enable" -m10 -min=0.000 -max=1.000 -i0"Disable" -i1"Enable" #404 -t2 -s1"Limited siganl active of X++" -s3"0:not enable,1:enable" -m10 -min=0.000 -max=1.000 -i0"Disable" -i1"Enable" #405 -t2 -s1"Limited siganl active of Y++" -s3"0:not enable,1:enable" -m10 -min=0.000 -max=1.000 -i0"Disable" -i1"Enable" #406 -t2 -s1"Limited siganl active of Z++" -s3"0:not enable,1:enable" -m10 -min=0.000 -max=1.000 -i0"Disable" -i1"Enable" #407 -t2 -s1"Limited siganl active of A++" -s3"0:not enable,1:enable" -m10 -min=0.000 -max=1.000 -i0"Disable" -i1"Enable" #408 -t2 -s1"Effective electric level of X--" -m10 -min=0.000 -max=1.000 -i0"Low" -i1"High" #409 -t2 -s1"Effective electric level of Y--" -m10 -min=0.000 -max=1.000 -i0"Low" -i1"High" #410 -t2 -s1"Effective electric level of Z--" -m10 -min=0.000 -max=1.000 -i0"Low" -i1"High" #411 -t2 -s1"Effective electric level of A--" -m10 -min=0.000 -max=1.000 -i0"Low" -i1"High" #412 -t2 -s1"Effective electric level of X++" -m10 -min=0.000 -max=1.000 -i0"Low" -i1"High" #413 -t2 -s1"Effective electric level of Y++" -m10 -min=0.000 -max=1.000 -i0"Low" -i1"High" #414 -t2 -s1"Effective electric level of Z++" -m10 -min=0.000 -max=1.000 -i0"Low" -i1"High" #415 -t2 -s1"Effective electric level of A++" -m10 -min=0.000 -max=1.000 -i0"Low" -i1"High" #374 -t2 -s1"Enable software limit" -s3"0:not enable,1:enable" -m11 -min=0.000 -max=1.000 -i0"Disable" -i1"Enable" #375 -t1 -s1"Soft-limited postion value of X--" -s2"mm" -m11 -min=-9999.000 -max=9999.000 #376 -t1 -s1"Soft-limited postion value of Y--" -s2"mm" -m11 -min=-9999.000 -max=9999.000 #377 -t1 -s1"Soft-limited postion value of Z--" -s2"mm" -m11 -min=-9999.000 -max=9999.000 #378 -t1 -s1"Soft-limited postion value of A--" -s2"deg" -m11 -min=-9999.000 -max=9999.000 #379 -t1 -s1"Soft-limited postion value of X++" -s2"mm" -m11 -min=-9999.000 -max=9999.000 #380 -t1 -s1"Soft-limited postion value of Y++" -s2"mm" -m11 -min=-9999.000 -max=9999.000 #381 -t1 -s1"Soft-limited postion value of Z++" -s2"mm" -m11 -min=-9999.000 -max=9999.000 #382 -t1 -s1"Soft-limited postion value of A++" -s2"deg" -m11 -min=-9999.000 -max=9999.000 #430 -t2 -s1"MPG interface type" -s3"0-serial port MPG£¬1-standard MPG" -m12 -min=0.000 -max=1.000 -i0"Serial" -i1"Standard" #431 -t1 -s1"MPG Precision" -m12 -min=0.001 -max=0.01 #432 -t2 -s1"Standard MPG signal Electric Level" -m12 -min=0.000 -max=1.000 -i0"Low" -i1"High" #434 -t2 -s1"A/B phase signal level on MPG" -m12 -min=0.000 -max=1.000 -i0"Low" -i1"High" #428 -t2 -s1"Enable the ESTOP signal on MPG" -s3"0:not enable,1:enable" -m12 -min=0.000 -max=1.000 -i0"Disable" -i1"Enable" #429 -t2 -s1"Electric level of ESTOP on MPG" -m12 -min=0.000 -max=1.000 -i0"Low" -i1"High" #423 -t2 -s1"Enable signal of extended ESTOP" -s3"0:not enable,1:enable" -m13 -min=0.000 -max=1.000 -i0"Disable" -i1"Enable" #424 -t2 -s1"Electric level of ext-ESTOP signal" -m13 -min=0.000 -max=1.000 -i0"Low" -i1"High" #425 -t2 -s1"Enable extended START&PAUSE" -s3"0:not enable,1:enable" -m13 -min=0.000 -max=1.000 -i0"Disable" -i1"Enable" #426 -t2 -s1"Electric level of extended START" -m0 -min=0.000 -max=1.000 -i0"Low" -i1"High" #427 -t2 -s1"Electric level of extended PAUSE" -m0 -min=0.000 -max=1.000 -i0"Low" -i1"High" #446 -t2 -s1"Define the extended key function" -m13 -min=0.000 -max=1.000 -i0"START" -i1"Find Middle" #447 -t2 -s1"Define the Function of Ext-key2" -m13 -min=0.000 -max=1.000 -i0"PAUSE" -i1"ZERO" #437 -t2 -s1"enable of X axis backlash" -s3"0:not enable,1:enable" -m14 -min=0.000 -max=1.000 -i0"Disable" -i1"Enable" #438 -t2 -s1"enable of Y axis backlash" -s3"0:not enable,1:enable" -m14 -min=0.000 -max=1.000 -i0"Disable" -i1"Enable" #439 -t2 -s1"enable of Z axis backlash" -s3"0:not enable,1:enable" -m14 -min=0.000 -max=1.000 -i0"Disable" -i1"Enable" #440 -t2 -s1"enable of A axis backlash" -s3"0:not enable,1:enable" -m14 -min=0.000 -max=1.000 -i0"Disable" -i1"Enable" #441 -t1 -s1"X axis backlash distance" -s2"mm" -m14 -min=0.000 -max=0.999 #442 -t1 -s1"Y axis backlash distance" -s2"mm" -m14 -min=0.000 -max=0.999 #443 -t1 -s1"Z axis backlash distance" -s2"mm" -m14 -min=0.000 -max=0.999 #444 -t1 -s1"A axis backlash distance" -s2"deg" -m14 -min=0.000 -max=9.999 #445 -t1 -s1"Backlash Speed" -s2"mm/min" -m14 -min=99.000 -max=99999.000 #267 -t1 -s1"H00 tool offset" -s2"mm" -m0 -min=-999.999 -max=999.999 #268 -t1 -s1"H01 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999 #269 -t1 -s1"H02 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999 #270 -t1 -s1"H03 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999 #271 -t1 -s1"H04 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999 #272 -t1 -s1"H05 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999 #273 -t1 -s1"H06 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999 #274 -t1 -s1"H07 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999 #275 -t1 -s1"H08 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999 #276 -t1 -s1"H09 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999 #277 -t1 -s1"H10 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999 #278 -t1 -s1"H11 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999 #279 -t1 -s1"H12 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999 #280 -t1 -s1"H13 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999 #281 -t1 -s1"H14 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999 #282 -t1 -s1"H15 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999 #283 -t1 -s1"D00 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999 #284 -t1 -s1"D01 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999 #285 -t1 -s1"D02 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999 #286 -t1 -s1"D03 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999 #287 -t1 -s1"D04 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999 #288 -t1 -s1"D05 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999 #289 -t1 -s1"D06 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999 #290 -t1 -s1"D07 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999 #291 -t1 -s1"D08 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999 #292 -t1 -s1"D09 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999 #293 -t1 -s1"D10 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999 #294 -t1 -s1"D11 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999 #295 -t1 -s1"D12 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999 #296 -t1 -s1"D13 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999 #297 -t1 -s1"D14 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999 #298 -t1 -s1"D15 tool offset" -s2"mm" -m15 -min=-999.999 -max=999.999 #299 -m0 #1 -t2 -s1"language setting" -s3"0:eng,1:chs" -m16 -min=0.000 -max=1.000 -i0"Eng" -i1"ÖÐÎÄ" #2 -t1 -s1"Display response during working" -m16 -min=400 -max=10000 #3 -t2 -s1"Function of tool path key" -m0 -min=0.000 -max=1.000 -i0"tool path" -i1"Try cutting" #218 -t2 -s1"Cycle Start key mode selection" -m16 -min=0.000 -max=1.000 -i0"Pause start" -i1"Restart" #499 -t1=888888.000 -s1"user access key" -m16 -min=0.000 -max=999999.000 #396 -t0=1600 -s1"Number of line" -m16 -min=100.000 -max=3600.000 #495 -t1 -s1"interpolation period" -s2"s" -m16 -min=0.002 -max=0.010 #497 -t1=0.000 #498 -t0=4.000 #18 -t1=200.0 #19 -t1=200.0 #20 -t1=3.0 #192 -t1=100.0 #193 -t1=100.0 #194 -t1=3.0 #250 -t2 -s1"real track paint enable" -m16 -min=0.000 -max=1.000 -i0"disable" -i1"enable" #253 -t2 -s1"track paint mode" -m16 -min=0.000 -max=1.000 -i0"Statue Mode" -i1"Line Mode" #88 -t2 -s1"enable of beep " -m16 -min=0.000 -max=1.000 -i0"Disable" -i1"Enable" #449 -s1"ZERO" #450 -s1"GOTOZ" #451 -s1"HOME" #452 -s1"PROBE" #453 -s1"AUTO" #454 -s1"SIMULATE" #455 -s1"CONT" #456 -s1"STEP" #457 -s1"MPG" #458 -s1"RESET" #459 -s1"READY" #460 -s1"BUSY" #461 -s1"FRO:" #462 -s1"SRO:" #463 -s1"SJR" #464 -s1"Start Line:" #465 -s1"2ND" #466 -s1"syntax check" #467 -s1"Main Page" #468 -s1"File Page" #469 -s1"Param Page" #470 -s1"Normal Mod" #471 -s1"X-:gotoz Y-:zero Z-:home" #472 -s1"A-:probe Start:goto break" #473 -s1"X-:all gotoz X+:x gotoz" #474 -s1"Y+:y gotoz Z+:z gotoz" #475 -s1"A-:go probe" #476 -s1"X+:left X-:right Y+:up Y-:down" #477 -s1"Z-:enter Z+:cancel" #478 -s1"Y-:all zero X+:x zero" #479 -s1"Y+:y zero Z+:z zero" #480 -s1"Z-:all home X+:x home" #481 -s1"Y+:y home Z+:z home" #482 -s1 "soft limit:" #483 -s1 "TRCUT" #484 -s1 "EDIT" #485 -s1 "SBK" #8=1.000 #9=1.000 #12=1.000 #13=1.000 #14=1.000 #195=0 #196=0 &&